Manual Bosch PBH 3000 FRE Set (page 19 of 112) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

708152

Zoom out

Zoom in

1/112

English | 19

Bosch Power Tools

1 609 92A 1LU | (23.5.18)

Note:

If the tool holder was opened to the stop, then a latching

noise possibly may be heard while closing the tool holder and

the tool holder will not close.

In this case, turn the front sleeve

once in anticlockwise di-

rection. Afterwards, the tool holder can be closed (tightened).

– Turn the mode selector switch 12 to the “drilling” position.

Removing Drilling Tools without SDS-plus from the Key-

less Chuck

(PBH 2900 FRE/PBH 3000 FRE Set/PBH 3000-2 FRE)

(see figure J)

– Firmly hold the rear sleeve 26 of the keyless chuck and

turn the front sleeve 25 of the keyless chuck in anticlock-

wise direction until the drilling tool can be removed.

Dust Extraction with the Dust Extraction Attach-

ment (Accessory)

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Mounting the Dust Extraction Attachment (see figure K)

For dust extraction, the dust extraction attachment (accesso-

ry) is required. When drilling, the dust extraction attachment

retracts so that the attachment head is always close to the

surface at the drill hole.

– Press the button for depth stop adjustment 15 and remove

the depth stop 18. Press button 15 again and insert the

dust extraction attachment into the auxiliary handle 17

from the front.

– Connect an extraction hose (diameter 19 mm, accessory) to

the extraction sleeve

of the dust extraction attachment.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Adjusting the Drilling Depth on the Dust Extraction At-

tachment (see figure L)

The required drilling depth X can also be adjusted when the

dust extraction attachment is mounted.

– Insert the SDS-plus drilling tool to the stop into the SDS-

plus tool holder 3. Otherwise, the movability of the SDS-

plus drilling tool can lead to incorrect adjustment of the

drilling depth.

– Loosen the wing bolt 31 on the dust extraction attach-

ment.

– Without switching the power tool on, apply it firmly to the

drilling location. The SDS-plus drilling tool must face

against the surface.

– Position the the guide pipe 32 of the dust extraction at-

tachment in its holding fixture in such a manner that the

head of the dust extraction attachment faces against the

surface to be drilled. Do not slide the guide pipe 32 further

over the telescopic pipe 30 of the dust extraction attach-

ment than required, so that as much as possible of the

scale 30 on the telescopic pipe remains visible.

– Retighten the wing bolt

again. Loosen the clamping screw

on the depth stop of the dust extraction attachment.

– Move the depth stop 29 on the telescopic pipe 30 in such

a manner that the clearance X shown in the figure corre-

sponds with the required drilling depth.

– Tighten the clamping screw 28 in this position.

Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Setting the operating mode

The operating mode of the power tool is selected with the

mode selector switch 12.

Note: Change the operating mode only when the machine is

switched off! Otherwise, the machine can be damaged.

– To change the operating mode, push the release button 11

and turn the mode selector switch 12 to the requested po-

sition until it can be heard to latch.

PBH 2800 RE/PBH 2900 RE/PBH 2900 FRE/

PBH 3000 FRE Set

Position for drilling without impact in

wood, metal, ceramic and plastic as well as

for screwdriving and thread cutting

Position for hammer drilling in concrete or

stone

Vario-Lock position for adjustment of the

chiselling position

The mode selector switch 12 does not latch

in this position.

Position for chiselling

OBJ_BUCH-318-007.book Page 19 Tuesday, November 10, 2015 5:05 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PBH 3000 FRE Set in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PBH 3000 FRE Set Manual

Product: