700757
14
Zoom out
Zoom in
Previous page
1/155
Next page
14
en Adjusting lever / seal for fruit pulp
Adjusting lever /
seal for fruit pulp
X Fig. F – Models with adjusting lever
for seal
The consistency of the juice can be
controlled using the adjusting lever for fruit
pulp.
For juice with a lot of fruit pulp, slide the
lever to the right (Ê
For juice with less fruit pulp, slide the
lever towards the centre (É
To clean/rinse out, remove the juice
drum, turn over and slide the lever to the
stop as shown (È
X Fig. G – Models with seal
The seal for fruit pulp ensures that the juice
has a constant consistency.
When making juice or sorbet, the seal
must sit correctly in the aperture for fruit
pulp.
To clean/rinse out, remove the juice
drum, turn over and pull out the seal.
Preparation
W Risk of injury
Do not insert the mains plug until all
preparations for working with the appliance
are complete and all individual parts are
assembled correctly and connected to the
base unit.
Caution!
Never place the juice drum onto the base
unit without the seal for the drive shaft.
Ensure that the seal also sits correctly after
placing it onto the base unit.
Important: Before re-assembling, check
that the aperture is completely closed by
the seal for fruit pulp. X “Adjusting lever /
seal for fruit pulp” see page 14
Preparing to squeeze juice
X Image sequence B
1. Place the base unit onto a stable and
level work surface.
2. Place the juice drum onto the base
unit. When doing so, align the recesses
on the base of the juice drum with the
counterparts on the base unit (observe
.
flush and firmly on top of the base unit.
3. Place the rotating brush into the juice
drum.
4. Place the desired strainer insert piece

(observe markings .
Important: Ensure that the aperture and
the notches on the base sit firmly on top of
their counterparts on the juice drum. The
strainer insert piece must not be able to turn
any further.
5. Place the juicer screw into the strainer
and press down until it sits on top of the
drive shaft.
6. Place the lid on top (,
it as far as possible in a clockwise
direction (;
Preparing to make sorbet
X Image sequence C
1. Place the base unit onto a stable and
level work surface.
2. Place the juice drum onto the base
unit. When doing so, align the recesses
on the base of the juice drum with the
counterparts on the base unit (observe
.
flush and firmly on top of the base unit.
3. Place the sorbet insert piece in the juice
drum (observe markings .
Important: Ensure that the aperture and
the notches on the base sit firmly on top of
their counterparts on the juice drum. The
sorbet insert piece must not be able to turn
any further.
4. Place the juicer screw into the sorbet
insert piece and press down until it sits
on top of the drive shaft.
5. Place the lid on top (,
it as far as possible in a clockwise
direction (;
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch MESM5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch MESM5 in the language / languages: All languages as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info