746511

Bosch MCM3PM386 - MultiTalent 3 Plus Manual

23
Zoom out
Zoom in
Previous page
1/204
Next page
23
en
Operation
Smart tool detection (MCM3P...)
Every speed setting is identified with a differ-
ent colour (grey and red). This colour coding
system can also be found on the acces-
sories. The accessories are automatically
connected to the right speed setting.
Low speed, grey
with drive shaft
For using tools and cutting discs.
High speed, red
without drive shaft
For using the blender and universal
cutter.
Preparation
Place the base unit on a smooth, clean
surface.
Pull cable out of the base unit to the
required length.
Important information
– Use only the rotary switch to switch the
appliance on or off.
– Never switch the appliance off by rotating
the bowl, the blender or a tool.
– Do not switch the appliance on unless
tools or accessories have been completely
attached.
Bowl with accessories/tools
W Risk of injury from the rotating tools!
While the appliance is operating, never place
fingers in the mixing bowl. Always use the
pusher for adding ingredients. After switching
off, the drive continues running for a short
time. Change tools only when the drive is at
a standstill.
Warning!
When working with the bowl, the appliance
cannot be switched on until the bowl has
been attached and the lid has been attached
and screwed on tight.
Universal blade
for cutting, mincing, mixing.
W Risk of injury from sharp blades!
Do not touch blades of the universal blade
with bare hands. When not in use, always
store the universal blade in the blade guard.
Grip the universal blade by the edge of the
plastic handle only.
Kneading hook
for kneading dough and mixing-in
ingredients that ought not be cut (e.g. raisins
and chocolate chips).
Beating disc
for cream, egg white and
mayonnaise.
Fig. B
Attach the bowl (arrow on bowl on dot on
the appliance .) and rotate as far as
possible in a clockwise direction (,).
Insert tool holder into the bowl.
Insert universal blade, whisking disc or
kneading hook into the tool holder and
release.
Note position of the tools when
inserting them! Press tools all the way
down.
Warning!
Do not add ingredients until the tools have
been inserted.
Add ingredients.
Attach lid with pusher (match arrow on
lid on dot on bowl .) and rotate in
a clockwise direction (,). Lid lug must be
located fully in the slot in the bowl handle.
Insert the mains plug.
Set the rotary switch to the desired setting.
To add more ingredients, set the rotary
switch to P.
Remove the pusher and add ingredients
through the feed tube. Pusher can be used
as a measuring cup.
Cutting discs
W Risk of injury from sharp blades!
Do not grip the sharp blades or edges of the
cutting discs. Grip the discs by the plastic
part in the centre only! Do not place fingers
in the feed tube. Only use the pusher when
adding more ingredients.
Slicing reversible disc –
thick/thin
for slicing fruit and vegetables.
Process at setting 1.
Identification on the reversible slicing disc:
“grob” for the thick cutting side,
“fein” for the thin cutting side
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch MCM3PM386 - MultiTalent 3 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch MCM3PM386 - MultiTalent 3 Plus in the language / languages: All languages as an attachment in your email.

The manual is 6,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info