786509

Bosch LR 60 Manual

17
Zoom out
Zoom in
Previous page
1/253
Next page
English | 17
Indicator Capacity
0 − 2%
Always replace all the batteries at the same time. Only use
batteries from the same manufacturer and which have the
same capacity.
uTake the batteries out of the laser receiver when you
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage in the laser receiver.
Rotary Laser Battery Charge Indicator
The battery charge indicator(a) shows the state of charge of
the battery pack/batteries of the rotary laser, provided that
the rotary laser is switched on and a Bluetooth® connection
has been established between the laser receiver and the
rotary laser.
Indicator Capacity
60 − 100%
30 − 60%
5 − 30%
0 − 5%
Operation
Starting operation
uProtect the laser receiver against moisture and direct
sunlight.
uDo not subject the laser receiver to extreme temperat-
ures or variations in temperature. As an example, do
not leave it in vehicles for longer periods. In case of large
variations in temperature, allow the laser receiver to ad-
just to the ambient temperature before putting it into op-
eration. In case of extreme temperatures or variations in
temperature, the accuracy of the laser receiver can be im-
paired.
uKeep the work area free from obstacles that could re-
flect or obstruct the laser beam. For example, cover
any reflective or shiny surfaces. Do not measure
through panes of glass or similar materials. The meas-
urements may be distorted by a reflected or obstructed
laser beam.
Setting up the laser receiver (seefigureA)
Position the laser receiver so that the laser beam can reach
the reception area(1). Align it so that the laser beam runs
straight through the reception area (as shown in the figure).
For rotary lasers with multiple operating modes, select the
horizontal or vertical operation with the highest rotational
speed.
Switching On/Off
uA loud audio signal sounds when switching on the
laser receiver. Therefore, keep the laser receiver
away from your ear or other persons when switching it
on. The loud sound can damage hearing.
To switch on the laser receiver, press the on/off
button(19). All display indicators and all LEDs light up
briefly and an audio signal sounds.
To switch off the laser receiver, press and hold the on/off
button(19) until all LEDs briefly light up and the display
goes out. With the exception of the setting for the display
lighting, all settings are saved when the laser receiver is
switched off.
If no button on the laser receiver is pressed for approx.
10min and no laser beam reaches the reception area(1) for
10min, then the laser receiver will automatically switch it-
self off to preserve battery life.
Connection to the Rotary Laser
In the default factory setting, the rotary laser and the sup-
plied laser receiver are already connected via Bluetooth®.
For the existing connection, the Bluetooth® connection
indicator(b) appears in the display of the laser receiver.
To reconnect the laser receiver or to connect an additional
laser receiver with the rotary laser, press and hold the
Bluetooth® button on the rotary laser until the symbol for es-
tablishing a connection to the remote control/laser receiver
appears in the display of the rotary laser. Then press and
hold the X‑axis button(16) and Y‑axis button(15) on the
laser receiver untilP‑‑ appears in the text display(e).
Confirmation as to whether a connection has successfully
been established will be shown on the display of the rotary
laser. POK will appear on the text indicator(e) of the laser
receiver.
If the connection between the rotary laser and the laser re-
ceiver cannot be established, PNK will appear in the text
display(e) of the laser receiver and the error message for a
failed connection will be shown in the display of the rotary
laser. For troubleshooting, consult the operating instruc-
tions for the rotary laser.
Direction indicators
The position of the laser beam in the reception area(1) is in-
dicated as follows:
– On the display(5) on the front and rear of the laser re-
ceiver by means of the "laser beam below centre line" dir-
ection indicator(f), the "laser beam above centre line"
direction indicator(j) and the centre line indicator(h)
– Optionally, by means of the red "laser beam below centre
line" LED direction indicator(4), the blue "laser beam
above centre line" LED direction indicator(2) and the
green centre line LED(3) on the front of the laser receiver
– By an audio signal (optional).
On the first pass of the laser beam through the reception
area(1) a short audio signal always sounds and the red
"laser beam below centre line" LED direction indicator(4)
and the blue "laser beam above centre line" LED direction
Bosch Power Tools 1 609 92A 7M6 | (12.05.2022)
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch LR 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch LR 60 in the language / languages: All languages as an attachment in your email.

The manual is 11.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info