Manual Bosch Intuvia Performance Line (page 37 of 159) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

590283

Zoom out

Zoom in

1/159

English–14

Bosch eBike Systems 0 276 001 SPI | (16.7.14)

Operation

Initial Operation

Connecting the charger to the mains (see figure E)

 Observe the mains voltage! The voltage of the power

supply must correspond with the data given on the name-

plate of the battery charger. Battery chargers marked with

230 V can also be operated with 220 V.

Plug the charger plug C3 of the power cord into the charger

socket C2 of the charger.

Connect the mains cable (country-specific) to the mains

supply.

Charging the removed battery (see figure F)

Switch the battery pack off and remove it from the holder of

the eBike. For this, read and observe the operating instruc-

tions of the battery pack.

 Place down the battery pack only on clean surfaces. In

particular, avoid soiling the charge socket and the con-

tacts, e. g. by means of sand or soil.

Insert the charger plug C5 of the battery charger into the

socket C6 on the battery pack.

Charging the battery on the Bike (see figure G)

Switch the battery off. Clean the cover of the charge socket

C7. Prevent especially the charge socket and the contacts

from getting dirty, e.g. by sand or soil. Lift the cover of the

charge socket C7 and plug the charge connector C5 into the

charge socket C6.

 Charge the battery only in accordance with all safety

instructions. If this is not possible, remove the battery

from the holder and charge it in a more suitable location.

When doing so, read and observe the operating instruc-

tions of the battery.

Charging Procedure

The charging procedure begins as soon as the charger is con-

nected to the battery or the charge socket on the bike and the

main power supply.

Note: The charging procedure is only possible when the tem-

perature of the battery pack is within the allowable charging-

temperature range.

Note: The drive unit is deactivated during the charging proce-

dure.

The battery can be charged with and without the cycle com-

puter. When charging without the cycle computer, the charg-

ing procedure can only be observed on the battery charge-

control indicator.

When the on-board computer is connected, the back lighting of

the display is switched on at low luminosity and “Charging/

xx% charged” appears on the display.

The cycle computer can be removed during the charging pro-

cedure, or it can also be fitted after the charging procedure

has begun.

The charging state is displayed by the battery charge-control

indicator A3 on the battery and by the bars on the cycle com-

puter.

When charging the main battery on the bike, the battery of the

cycle computer can also be charged.

During the charging procedure, the LEDs of charge-control in-

dicator A3 on the battery pack light up. Each continuously lit

LED is equivalent to a charge capacity of approx. 20 %. The

flashing LED indicates the charging of the next 20 %.

 Use caution when touching the charger during the

charging procedure. Wear protective gloves. Especially

in high ambient temperatures, the cha

rger can heat up

considerably.

Once the battery is fully charged, the LEDs extinguish imme-

diately and the cycle computer is switched off. The charging

procedure is terminated. The charging state can be displayed

for 3 seconds by pressing the on/off button A4.

Disconnect the charger from the main power supply and the

battery pack from the charger.

When disconnecting the battery pack from the charger, the

battery pack is automatically switched off.

Note: If you have charged on the bike, carefully close the

charge socket C6 with the cover C7 after the charging proce-

dure so that no dirt or water can get in.

If the charger is not disconnected from the battery after

charging, after a few hours the charger will switch itself back

on, check the charging state of the battery and begin the

charging procedure again if necessary.

Troubleshooting – Causes and Corrective

Measures

Cause Corrective Measure

Two LEDs of the battery

pack flashing

Battery pack defective Refer to an authorised bicycle

dealer

Three LEDs of the battery

pack flashing

Battery pack too warm or too

cold

Disconnect the battery from

the charger until the charging

temperature range has been

reached.

Do not connect the battery

pack to the charger until it has

reached the allowable charg-

ing temperature.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Intuvia Performance Line in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Intuvia Performance Line Manual

Product: