764283
29
Zoom out
Zoom in
Previous page
1/318
Next page
English | 29
Problem Possible Cause Corrective Measure
Rough mowing conditions Select "uneven ground/low sensitivity" option from menu
item "lawn condition/bump sensor".
Flatten garden/remove/bumps/mark out unsuitable
areas with the perimeter wire – Please follow the instruc-
tions in the Installation Guide.
Grass too long Select "uneven ground/low sensitivity" option from menu
item "lawn condition/bump sensor".
Slopes in garden too steep Ensure mower only operates on slopes of 15 degrees or
less and full garden is not on a slope.
Mower gets stuck in
garden Objects/obstacles not marked out Use the perimeter wire to mark off obstacles where the
mower often gets stuck.
Newly laid turf Allow a few weeks for the soil to settle before using the
mower.
Change setting in menu item "lawn condition / bump
sensor" to low sensitivity / uneven.
After watering, wait as long as possible until you start the
mower.
Mower unintentionally
cuts flowers, etc. or
runs over certain
obstacles
Objects/obstacles below 5cm not marked
out Mark obstacle using perimeter wire leaving 30cm from
object or remove objects/obstacles.
Mower does not ap-
pear to cut logically LogiCut system depends on the garden
conditions. Mower does not necessarily
have to continue in the next uncut area.
Further information can be found on the Installation
Guide.
If behaviour re-occurs often, remap lawn area.
Mower does not always go in a straight line
when travelling between areas No corrective action needed.
Mower frequently does not find right posi-
tion or turns on the spot Change wire ID.
Wire crossed while marking an object Follow instructions in the Installation Guide.
Mower runs in random paths in an addi-
tional lawn without docking station. Normal behaviour. The LogiCut system only works in
areas with docking station.
Perimeter wire keeps
being cut Wire is not taut between pegs
Distance between pegs is more than 75cm
Make wire taut and ensure distance between pegs is
maximum 75cm. Use the wire connectors to repair the
cut. Avoid using a verticutter, scarifier, etc. over the peri-
meter wire.
Mower leaves ragged
finish/poor quality of
cut
The mower does not mow often enough Mow more frequently for a good result (e.g. by means of
more/longer slots in schedule).
Cutting blades blunt Reverse or replace cutting blades (see figure J).
Possible clogging Always turn isolator switch off first, then check under-
neath the mower. Clear out as necessary (always wear
protective gloves).
Perimeter wire not
detected No power at the docking station Check if the docking station is powered up (LED is on).
Perimeter wire damaged/cut Check perimeter wire for damage.
Wrong installation (e.g. not enough dis-
tance between wires) Follow instructions in the Installation Guide.
Perimeter wire close to a source of interfer-
ence Remove any excess (e.g. coiled up) perimeter wire
around the docking station. Change perimeter wire ID in
the menu.
Bosch Power Tools F 016 L94 037 | (11.11.2020)
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Indego XS 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Indego XS 300 in the language / languages: All languages as an attachment in your email.

The manual is 4,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info