Manual Bosch Indego 1200 Connect (page 37 of 466) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591351

Zoom out

Zoom in

1/466

English | 37

Bosch Power Tools F 016 L81 115 | (7.10.14)

Lawn Preparation

Remove stones, loose pieces of wood, wire, live mains cables

and other foreign objects from the cutting area.

Make sure that the cutting area is even and has no ditches,

grooves and steep slopes above 20° that are clear obstruc-

tions for the machine.

Cut the main area of the lawn with a conventional mower to a

max. height of 40 mm and the perimeter wire area to a max.

height of 20 mm.

Installation

For a video guide on how to install the Indego please visit

www.bosch-indego.com or use the following QR-Code.

Select a position for the docking station, horizontally levelled

and out of direct sunlight.

Note: The docking station must be positioned on the wire at

an outer edge of the cutting area. It cannot be positioned by

the side of a shed or workshop that appears as an island with-

in the cutting area.

Make sure that the docking station is placed beside the cut-

ting area with a straight 1.5 m track in front of the docking sta-

tion and a straight 1 m track behind. Whilst stood in the grass

area to be cut it is important that the docking station charging

pins point to the left. (see figure 2)

Note: If the docking station is positioned with the charging

pins pointing either into the grass area or pointing to the right

the Indego will not run correctly.

Pull the wire end through the front hole of the base plate and

straight through the wire duct and the rear hole. Fix the wire

with a peg inline with the hole. Cut off insulation carefully and

connect the wire to the right hand (red) terminal. (see

figures 4– 5)

Fix the docking station with 4 supplied fixing pins to the

ground. (see figure 6)

Lay out the perimeter wire anti-clockwise and flush to the

ground. Observe the minimum distances from lawn edges,

steps, walls, ponds, etc. Use the spacing guide. (see figure 7)

Note: The cable should be positioned so that the Indego will

not be more than 16 m away at anytime.

If the working area borders against a flat path or surface that

is level with the lawn the Indego will be able to run over it. In

such cases the perimeter wire should be positioned right up

to the edge of the lawn.

Note: Perimeter wire can be buried up

to a maximum depth of 5 cm. It is recommended to mark out

permanent objects within the garden. This will prevent the In-

dego colliding with the object and reduce wear on the shell.

Objects on the lawn below 6 cm height e.g. trees, ponds, flow-

er beds etc. must be delimited in a clockwise direction. The

lines to and from these zones may not cross but the wire

should be touching. (see figure 7)

Note: Approximately 20 cm of lawn

around the fixed object and around the

edge of the lawn will not be mown.

Fix the wire with the first peg next to the docking station, ten-

sion and fix with pegs at a distance of approx. 50 cm. (see

figure 7)

Continue the loop and bring the wire to the back of the dock-

ing station and inline with the other end of the wire. Fix the

second end of the wire also with the peg. Perimeter wire and

peg should be installed inline. Shorten the wire, cut off insula-

tion carefully and connect the wire to the left hand (black) ter-

minal. (see figure 10)

Clip on the protective cover of the docking station. (see

figure 11)

Note: If extra perimeter wire is required this can be added us-

ing one connector. (see figure 8)

The wire can be extended up to the maximum allowed length

of 450 m.

Note: If verticutting or raking is intended avoid the perimeter

wire.

Install the power supply in a cool, dry environment. Connect it

with the docking station and an indoor mains socket. (see

figure 12)

Check the indicator on the docking station (see figure 13):

–Indicator lights up continuously green, if the output volt-

age of the power supply is available and the perimeter wire

is not interrupted.

–Indicator does not light up when the output voltage of the

power supply is not available.

Installing an additional lawn

(Indego 1300)

The Indego 1300 can be used in up to three different lawns.

To install an additional cutting area/lawn you will need to have

purchased an additional docking station (F 016 800 384/

F 016 800 438) and the required perimeter wire and pegs.

To install the additional area please follow the installation in-

structions from the beginning of this section.

Plug in isolator key

14 9

Charge battery by putting the machine

into docking station 15 10

Welcome screen = Refer to manual

16 10

Lift up and carry the machine

17 11

Set height of cut

18 11

Logicut Intelligent Cutting

19 12

Cleaning

A 13

Maintenance

B 13

Action Figure Page

20-25cm

OBJ_BUCH-1573-007.book Page 37 Tuesday, October 7, 2014 12:49 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Indego 1200 Connect in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Indego 1200 Connect

Bosch Indego 1200 Connect Installation Guide - Dutch - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Indego 1200 Connect Manual

Product: