743501
8
Zoom out
Zoom in
Previous page
1/60
Next page
8
Installation
6 720 604 683 (03.10)
Deutsch
Adernbelegung:
1 = Spannungsversorgung 17...24 V DC
2 = Datenleitung (BUS-High)
•4 = GND
6 = Datenleitung (BUS-Low).
2.2.2 Anschluss 230 V AC
B Unter Berücksichtigung der geltenden Vor-
schriften für den Anschluss mindestens Elek-
trokabel der Bauart H05VV-... (NYM-...)
verwenden.
B Zu den Anlagenteilen, Elektrokabel mit glei-
cher Qualität verwenden.
B Leitungen unbedingt wegen Tropfwasser-
schutz durch die bereits vormontierten Tüllen
führen und zugentlasten.
B Die Leitungsabdeckung unbedingt montieren.
Sie gewährleistet sicheren Schutz zwischen
Netz- und Niederspannungsseite (Bild 11).
Bei Anschluss mehrerer Verbraucher (Heizgerät
usw.):
B Wenn die max. Stromaufnahme den Wert der
vorgeschalteten Trennvorrichtung mit
min. 3 mm Kontaktabstand (z. B. Sicherung,
LS-Schalter) überschreitet, sind die Verbrau-
cher getrennt abzusichern.
2.2.3 Wichtige Hinweise
Wenn die Brücke zwischen den Klemmen 13
und 14 entfernt wird, bleibt die Umwälzpumpe
(P) stehen.
Anschluss TA 270 oder TA 300 (Bild 13):
In Verbindung mit TA 270 oder TA 300 sind alle
Funktionen aktiv!
B Speichertemperaturfühler (SF) und Speicher-
ladepumpe (LP) am HSM anschließen
-oder-
B Speichertemperaturfühler (SF) und falls benö-
tigt, die Speicherladepumpe (LP) am Heizge-
rät anschließen.
Gemeinsamer Vorlauftemperaturfühler (VF) bei
Kaskade:
B Vorlauftemperaturfühler am HSM mit Kodie-
rung „1“ anschließen.
B Bei Verwendung der hydraulische Weiche
aus dem Zubehörprogramm, den beiliegen-
den Tauchfühler am HSM mit Kodierung „1“
anschließen.
Anschluss TA 271 oder TA 301 (Bild 14):
In Verbindung mit TA 271 oder TA 301 sind alle
Funktionen aktiv!
B Speichertemperaturfühler (SF) und Speicher-
ladepumpe (LP) am HSM anschließen.
Anschluss TA 250 (Bild 15)
oder TR 220 (Bild 16):
In Verbindung mit TA 250 oder TR 220 ist nur die
Ansteuerung der Zirkulationspumpe möglich!
B Speichertemperaturfühler (SF) und falls benö-
tigt, die Speicherladepumpe (LP) am Heizge-
rät anschließen.
i
Die maximale Leistungsaufnahme
der Anlagenteile darf die Vorga-
ben nicht überschreiten (siehe
Kapitel 1.2).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch HSM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch HSM in the language / languages: German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info