17
Note: For details on which accessories are suitable for the self-
cleaning programme, please see the optional accessory table
at the start of these instructions.
Setting the cleaning level
1. Press the q button.
Cleaning level 3 is suggested. You can start the self-cleaning
immediately by pressing the
n button.
If you wish to change the cleaning level:
2. Select the desired cleaning level using the rotary selector.
3. Press the n button to start the cleaning operation.
The oven door locks shortly after operation starts. The
H
symbol lights up to indicate that the lock has been activated.
Once cleaning has finished
The oven stops heating. The cleaning time is shown in the
status bar as 00:00:00. You will not be able to open the oven
door until the
H symbol goes out.
Cancelling cleaning
Switch off the oven with
%. The oven door remains locked
while the
H symbol is lit.
Adjusting the cleaning level
Once cleaning starts, the cleaning level can no longer be
changed.
Setting cleaning to run overnight
So that you can use your oven throughout the day, delay the
end of the cleaning process to during the night. See the Time-
setting options section, setting a later end time.
After self-cleaning
Once the cooking compartment has cooled down, wipe out the
ash that has been left behind in the cooking compartment with
a damp cloth.
Care and cleaning
With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
■ Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
■ Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■ Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
■ sharp or abrasive cleaning agents,
■ cleaning agents with a high concentration of alcohol,
■ hard scouring pads or sponges,
■ high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Area Cleaning agents
Oven front Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
glass scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues.
Special stainless steel cleaning prod-
ucts suitable for warm surfaces are avail-
able from our after-sales service or from
specialist retailers. Apply a thin layer of
the cleaning product with a soft cloth.
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Door cover Stainless steel cleaning agents (available
from our after-sales service or from spe-
cialist retailers):
Please observe the manufacturer's
instructions.
Cooking compart-
ment
Hot soapy water or a vinegar solution:
Clean with a dish cloth.
If there are heavy deposits of dirt, use a
stainless steel scouring pad or oven
cleaner. Only use when the cooking
compartment is cold.
It is best to use the self-cleaning function.
Observe the instructions in the Self-clean-
ing section when doing so.
Glass cover for the
oven light
Hot soapy water:
Clean with a dish cloth.
Shelves Hot soapy water:
Soak and clean with a dish cloth or
brush.
Telescopic shelves Hot soapy water:
Clean with a dish cloth or a brush.
Do not soak. Clean in the dishwasher, or
in the oven as part of the self-cleaning
programme. The rails may be damaged
causing them to jam.
Accessories Hot soapy water:
Soak and clean with a dish cloth or
brush.
Area Cleaning agents
