7
Cooking compartment
The cooking compartment has four shelf positions. The shelf
positions are counted from the bottom up.
Caution!
■ Do not place anything on the cooking compartment floor. Do
not cover it with aluminium foil. A build-up of heat could
damage the appliance.
The cooking compartment floor and the evaporator dish must
always be kept clear. Always place ovenware in a perforated
cooking container or on a wire rack.
■ Do not slide any accessories between the shelf positions, or
they may tip.
Optional accessories
You can obtain further accessories from specialist retailers:
Before using for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
■ Setting the clock
■ Setting the water hardness range
■ Starting the appliance for the first time
■ Cleaning the accessories before use
Setting the clock
After the power has been connected, the0 symbol and ‹‹:‹‹
light up in the display. Set the clock.
1. Press the
0 button.
The time
‚ƒ:‹‹ is shown in the display.
2. Use the
@ or A button to set the clock.
After a few seconds, the time which has been set is adopted.
Setting the water hardness range
Descale your appliance regularly. This is the only way to
prevent damage.
Your appliance automatically displays when it needs descaling.
It has been preset to water hardness range "medium". Change
the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
If your water is very hard, we recommend that you use softened
water.
You can only dispense with descaling completely if you
exclusively use softened water. If this is the case, change the
water hardness to "softened".
You can change the water hardness range in the basic settings
when the appliance is switched off.
1. If required, turn the operating mode selector to
Û to switch off
the appliance.
2. Press and hold the
0 button until ™‹ „ appears in the
display.
3. Press the
0 button repeatedly until ™† ƒ appears
(“medium” water hardness range).
4. Press the
@ or A button to change the water hardness range.
Possible values:
5. Press and hold the
0 button to exit basic settings.
The change is saved.
Before first use
Before first use, heat the empty appliance for 20 minutes at
100 °C using
è Steam. Do not open the appliance door
during this time. The appliance is automatically calibrated (see
section: Automatic calibration).
1. Fill and insert the water tank (see section: Filling the water
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
2. Turn the operating mode selector to
è Steam.
3. Turn the temperature selector to 100 °C.
4. Press the n button.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
5. To switch off the appliance, turn the operating mode and
temperature selectors to
Û.
Leave the appliance door ajar until the appliance has cooled
down.
(YDSRUDWRUGLVK
5DLOVIRU
DFFHVVRULHV
7DQNUHFHVV
ZLWKZDWHUWDQN
Accessories Order no.
Cooking container, solid, GN
Z, 40 mm
deep
HEZ36D453
Cooking container, perforated, GN
Z,
40 mm deep
HEZ36D453G
Cooking container, solid, GN
Z, 28 mm
deep (baking tray)
HEZ36D452
Cooking container, solid, GN
Y, 40 mm
deep
HEZ36D153
Cooking container, perforated, GN
Y,
40 mm deep
HEZ36D153G
Porcelain cooking container, solid, GN
Z
HEZ36D353P
Porcelain cooking container, solid, GN
Y
HEZ36D153P
Wire rack HEZ36DR4
Cleaning sponge 643 254
Descaler 311 138
Honeycomb microfibre cloth 460 770
™† ‹
softened -
™† ‚
1-soft I
™† ƒ
2-medium II
™† „
3-hard III
™† …
4-very hard IV
