551208
16
Zoom out
Zoom in
Previous page
1/28
Next page
16
Installation
During installation, make sure that the lettering "top right" is
upside down at the bottom left of both panels.
1.Insert the lower panel at an angle towards the back (fig. A).
2.Slide in the middle panel (fig. B).
3.Stick the retaining clips onto the right and left-hand side of
the panel, aligning them so that the retaining carriers are over
the screw holes, and then screw into place (fig. C).
4.Hook the seal in to the bottom of the panel again (fig. D).
5.Insert the uppermost panel at an angle to the back into the
brackets. Take care not to push the seal to the back (fig. E).
6.Insert the two small seals on the left and right of the panel
again (fig. F).
7.Put the cover back in place and screw it on.
8.Attach the oven door.
Do not use the oven again until the panels have been
correctly installed.
Troubleshooting
Malfunctions often have simple explanations. Refer to the table
before calling the after-sales service as you may be able to
remedy the fault yourself.
Malfunction table
If a dish doesn't turn out as well as you had hoped, refer to the
section Tested for you in our cooking studio, where you will
find plenty of cooking tips and tricks.
Error messages
If an error message with
appears, press the 0 button. Then
reset the clock. If the error message appears again, call the
after-sales service.
You can take remedial action yourself if the following error
messages are displayed.
%$
'
&
)
(
Problem Possible cause Remedy/information
The oven does
not work.
The circuit
breaker is
defective.
Look in the fuse box and
check that the circuit
breaker is in working order.
Power cut Check whether the kitchen
light or other kitchen appli-
ances are working.
0 and zeros
light up in the
display.
Power cut Reset the clock.
The oven does
not heat up.
There is dust on
the contacts.
Turn the control knobs back
and forth several times.
The oven door
cannot be
opened. The L
symbol lights
up in the dis-
play.
The oven door
is locked by
q
self-cleaning.
Wait until the oven has
cooled down and the L
symbol goes out.
The oven does
not heat up. The
colon in the dis-
play flashes.
The oven is in
demonstration
mode.
Switch off the circuit
breaker in the fuse box and
switch it on again after
approximately 20 seconds.
Now, within approx.
2 minutes, press and hold
the
D button for approx.
4 seconds until the colon
lights up constinuously.
F8 appears in
the display.
Automatic
switch-off has
been activated.
Turn the function selector to
the off position.
Error message Possible cause Remedy/information
“‹‚‚
A button was
depressed for
too long or is
covered up.
Press all buttons individu-
ally. Check whether any but-
tons are jammed, covered
up or soiled.
“‹‚†
The tempera-
ture in the cook-
ing
compartment is
too high.
The oven door locks and
heating is suspended. Wait
until the oven has cooled
down. Press the
0 button
and reset the clock.
Problem Possible cause Remedy/information
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch HBA63B261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch HBA63B261 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info