Manual Bosch GWX 18V-15 PSC (page 31 of 499) (All languages)

786203

Zoom out

Zoom in

1/499

English | 31

Protective guard for grinding

Place the protective guard

(15) onto the holder on the

power tool until the coding

cams of the protective guard

are aligned with the holder.

When doing so, press and

hold the unlocking lever (1).

Press the protective guard

(15) onto the spindle collar

until the shoulder of the pro-

tective guard is sitting on the

flange of the power tool and

rotate the protective guard

until it audibly clicks into

place.

Adjust the position of the protective guard (15) to meet the

requirements of the operation. To do this, push the unlock-

ing lever (1) upward and rotate the protective guard (15)

into the required position.

uAlways position the protective guard(15) such that

the two cams on the unlocking lever(1) engage in the

corresponding openings on the protective guard(15).

uAdjust the protective guard (15) such that sparking in

the direction of the operator is prevented.

uThe protective guard (15) must only be adjustable

while the unlocking lever (1) is actuated. Otherwise,

the power tool must not be used any more under any

circumstances and must be sent to the after-sales ser-

vice.

Note: The coding cams on the protective guard (15) ensure

that only a protective guard that is suitable for the power

tool can be fitted.

Protective guard for cutting

uFor cutting, always use the protective guard for

cutting(17) or the protective guard for grinding (15)

together with the cover for cutting(18).

uProvide sufficient dust extraction when cutting stone.

The protective guard for cutting(17) is fitted in the same

way as the protective guard for grinding(15).

Metal cover for cutting

Fit the metal cover for cutting(18) on the protective guard

for grinding(15) (see figureA): Swivel the tool retainer back

(). Attach the cover(18) to the protective guard for

grinding(15) (). Press the tool retainer firmly into place

on the protective guard(15) ().

To remove the cover (see figureB), press the button on the

tool retainer () and swivel it back (). Remove the

cover(18) from the protective guard(15) ().

Plastic cover for cutting

Attach the plastic cover for cutting(18) to the protective

guard for grinding(15) (see figureC). The cover(18) aud-

ibly and visually engages on the protective guard(15).

To remove the cover (see figureD), unlock the cover(18) on

the left- or right-hand side of the protective guard(15) ()

and remove the cover ().

Extraction guard for cutting with a guide block

The extraction guard for cutting with a guide block (29) is fit-

ted in the same way as the protective guard for grinding

(15).

Hand guard

uAlways fit the hand guard (22) when working with the

rubber sanding pad (23) or with the cup brush/conical

brush/diamond annular cutter.

Attach the hand guard (22) to the side handle (11).

Standard auxiliary handle/low-vibration auxiliary handle

Screw the auxiliary handle (11)/(12) on the right or left of

the machine head depending on the working method.

uDo not operate your power tool without the auxiliary

handle(11)/(12).

uDo not continue to use the power tool if the auxiliary

handle (11)/(12) is damaged. Do not make any altera-

tions to the auxiliary handle (11)/(12).

The low-vibration auxiliary

handle (12) reduces vibra-

tion, enabling the tool to be

used safely and more com-

fortably.

Fitting and removing abrasive tools

Follow the special assembly instructions for

X-LOCK application tools.

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

uOnly use original X-LOCK application tools that carry the

X-LOCK logo. A maintained clamping gauge of max.

1.6mm can only be guaranteed with original X-LOCK ap-

plication tools. A higher clamping gauge can lead to insec-

ure clamping, potentially causing the clamp tool to come

loose.

uX-LOCK application tools do not need additional clamping

flanges or support flanges.

uMake sure that the application tool and the holder are not

deformed and are free from dirt and particles.

Pay attention to the dimensions of the abrasive tools.

Make sure that both X-LOCK catches are open (see figure

below) before fitting the X-LOCK application tool.

If necessary, clean the area between the two X-LOCK

catches.

Fitting the abrasive tool

Place the grinding/cutting/flap disc in a central position

on the X-LOCK holder, parallel to the bearing surface

and with the right side facing up.

Push the disc into the holder.

Bosch Power Tools 1 609 92A 6WT | (24.06.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 18V-15 PSC in the language / languages: All languages as an attachment in your email.

The manual is 29.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GWX 18V-15 PSC Manual

Product: