Manual Bosch GWX 18V-15 P (page 24 of 499) (All languages)

786202

Zoom out

Zoom in

1/499

24 | English

uDo not expose a battery pack or tool to fire or excess-

ive temperature. Exposure to fire or temperature above

130°C may cause explosion.

uFollow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specified in the instructions. Charging improperly or at

temperatures outside the specified range may damage

the battery and increase the risk of fire.

Service

uHave your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

uNever service damaged battery packs. Service of bat-

tery packs should only be performed by the manufacturer

or authorized service providers.

Safety warnings for angle grinder

Safety warnings common for grinding, sanding, wire

brushing or cutting-off operations:

uThis power tool is intended to function as a grinder,

sander, wire brush, hole cutter or cut-off tool. Read all

safety warnings, instructions, illustrations and spe-

cifications provided with this power tool. Failure to fol-

low all instructions listed below may result in electric

shock, fire and/or serious injury.

uOperations such as polishing are not to be performed

with this power tool. Operations for which the power

tool was not designed may create a hazard and cause per-

sonal injury.

uDo not convert this power tool to operate in a way

which is not specifically designed and specified by the

tool manufacturer. Such a conversion may result in a

loss of control and cause serious personal injury.

uDo not use accessories which are not specifically de-

signed and specified by the tool manufacturer. Just

because the accessory can be attached to your power

tool, it does not assure safe operation.

uThe rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

uThe outside diameter and the thickness of your ac-

cessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be ad-

equately guarded or controlled.

uThe dimensions of the accessory mounting must fit

the dimensions of the mounting hardware of the

power tool. Accessories that do not match the mounting

hardware of the power tool will run out of balance, vibrate

excessively and may cause loss of control.

uDo not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess

wear, wire brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for damage or in-

stall an undamaged accessory. After inspecting and

installing an accessory, position yourself and bystand-

ers away from the plane of the rotating accessory and

run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this test time.

uWear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing pro-

tectors, gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments. The eye

protection must be capable of stopping flying debris gen-

erated by various applications. The dust mask or respir-

ator must be capable of filtrating particles generated by

the particular application. Prolonged exposure to high in-

tensity noise may cause hearing loss.

uKeep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

uHold the power tool by insulated gripping surfaces

only, when performing an operation where the cutting

tool may contact hidden wiring. Contact with a "live"

wire will also make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

uNever lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may

grab the surface and pull the power tool out of your con-

trol.

uDo not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

uRegularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

uDo not operate the power tool near flammable materi-

als. Sparks could ignite these materials.

uDo not use accessories that require liquid coolants.

Using water or other liquid coolants may result in electro-

cution or shock.

Kickback and related warnings:

Kickback is a sudden reaction to a pinched or snagged rotat-

ing wheel, backing pad, brush or any other accessory. Pinch-

ing or snagging causes rapid stalling of the rotating access-

ory which in turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s rotation

at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either

jump toward or away from the operator, depending on direc-

tion of the wheel’s movement at the point of pinching. Abras-

ive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

1 609 92A 6WT | (24.06.2022) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 18V-15 P in the language / languages: All languages as an attachment in your email.

The manual is 29.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GWX 18V-15 P Manual

Product: