Manual Bosch GWX 18V-10 SC (page 24 of 483) (All languages)

786186

Zoom out

Zoom in

1/483

24 | English

Kickback and related warnings:

Kickback is a sudden reaction to a pinched or snagged rotat-

ing wheel, backing pad, brush or any other accessory. Pinch-

ing or snagging causes rapid stalling of the rotating access-

ory which in turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s rotation

at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either

jump toward or away from the operator, depending on direc-

tion of the wheel’s movement at the point of pinching. Abras-

ive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

uMaintain a firm grip with both hands on the power tool

and position your body and arms to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start-up. The operator can con-

trol torque reactions or kickback forces, if proper precau-

tions are taken.

uNever place your hand near the rotating accessory.

Accessory may kickback over your hand.

uDo not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point of snagging.

uUse special care when working corners, sharp edges,

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

uDo not attach a saw chain woodcarving blade, seg-

mented diamond wheel with a peripheral gap greater

than 10 mm or toothed saw blade. Such blades create

frequent kickback and loss of control.

Safety warnings specific for grinding and cutting-off

operations:

uUse only wheel types that are specified for your power

tool and the specific guard designed for the selected

wheel. Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

uThe grinding surface of centre depressed wheels must

be mounted below the plane of the guard lip. An im-

properly mounted wheel that projects through the plane

of the guard lip cannot be adequately protected.

uThe guard must be securely attached to the power tool

and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

uWheels must be used only for specified applications.

For example: do not grind with the side of cut-off

wheel. Abrasive cut-off wheels are intended for peri-

pheral grinding, side forces applied to these wheels may

cause them to shatter.

uAlways use undamaged wheel flanges that are of cor-

rect size and shape for your selected wheel. Proper

wheel flanges support the wheel thus reducing the pos-

sibility of wheel breakage. Flanges for cut-off wheels may

be different from grinding wheel flanges.

uDo not use worn down wheels from larger power tools.

A wheel intended for larger power tool is not suitable for

the higher speed of a smaller tool and may burst.

uWhen using dual purpose wheels always use the cor-

rect guard for the application being performed. Failure

to use the correct guard may not provide the desired level

of guarding, which could lead to serious injury.

Additional safety warnings specific for cutting-off

operations:

uDo not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading

and susceptibility to twisting or binding of the wheel in

the cut and the possibility of kickback or wheel breakage.

uDo not position your body in line with and behind the

rotating wheel. When the wheel, at the point of opera-

tion, is moving away from your body, the possible kick-

back may propel the spinning wheel and the power tool

directly at you.

uWhen the wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold it

motionless until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel from the

cut while the wheel is in motion otherwise kickback

may occur. Investigate and take corrective action to elim-

inate the cause of wheel binding.

uDo not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

uSupport panels or any oversized workpiece to minim-

ize the risk of wheel pinching and kickback. Large

workpieces tend to sag under their own weight. Supports

must be placed under the workpiece near the line of cut

and near the edge of the workpiece on both sides of the

wheel.

uUse extra caution when making a “pocket cut” into ex-

isting walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects

that can cause kickback.

uDo not attempt to do curved cutting. Overstressing the

wheel increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility of

kickback or wheel breakage, which can lead to serious in-

jury.

Safety warnings specific for sanding operations:

uUse proper sized sanding disc paper. Follow manufac-

turers recommendations, when selecting sanding pa-

1 609 92A 766 | (17.02.2022) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 18V-10 SC in the language / languages: All languages as an attachment in your email.

The manual is 17.03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GWX 18V-10 SC Manual

Product: