786309

Bosch GWX 17-125 Manual

25
Zoom out
Zoom in
Previous page
1/347
Next page
English | 25
To restart the tool, set the on/off switch (4) to the off posi-
tion and then switch the power tool on again.
Starting current limitation
The electronic starting current limitation feature restricts the
power of the power tool when it is switched on and enables
operation using a 16 A fuse.
Note: If the power tool runs at full speed immediately after
being switched on, this means that the starting current limit-
ation and restarting protection mechanisms have failed. The
power tool must be sent to the after-sales service immedi-
ately; see the "After-Sales Service and Application Service"
section for addresses.
Constant Electronic control
The Constant Electronic keeps the speed at no load and un-
der load virtually consistent, guaranteeing uniform perform-
ance.
Speed preselection (GWX ... S/T)
You can preselect the required speed using the thumbwheel
for speed preselection (5), even during operation. The re-
quired speed depends on the material and the working con-
ditions; it can be ascertained through practical tests.
Thumbwheel pos-
ition No-load speed
[min-1]No-load speed
[min-1]
GWX 13-125 S/
17-125 S/
19-125 S
GWX 17-125 T
1 2800 2800
2 4500 4100
3 6300 5400
4 8200 6700
5 9800 8000
6 11,500 9300
uThe rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
Working Advice
uPull the plug out of the socket before carrying out any
work on the power tool.
uExercise caution when cutting slots in structural walls;
see the "Information on structural design" section.
uClamp the workpiece if it is not secure under its own
weight.
uDo not load the power tool so heavily that it comes to a
stop.
uIf the power tool has been subjected to a heavy load,
continue to run it at no-load for several minutes to
cool down the accessory.
uDo not use the power tool with a cut-off stand.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
Rough grinding
uNever use cutting discs for rough grinding.
The best rough grinding results are achieved with a set angle
of 30° to 40°. Move the power tool back and forth with mod-
erate pressure. This will ensure that the workpiece does not
become too hot or discolour and that grooves are not
formed.
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked. Flap discs have a considerably higher ser-
vice life, lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
uAlways use the protective guard for cutting (9) when
cutting bonded abrasives.
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
The power tool must always
work in an up-grinding mo-
tion. Otherwise, there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
Cutting stone
uProvide sufficient dust extraction when cutting stone.
uWear a dust mask.
uThe power tool may be used only for dry cutting/grind-
ing.
For best results when cutting stone, use a diamond cutting
disc.
When using the extraction guard for cutting with a guide
block (18), the vacuum cleaner must be approved for vacu-
uming stone dust. Suitable vacuum cleaners are available
from Bosch.
Switch on the power tool
and position it with the
front part of the guide block
on the workpiece. Move the
power tool with a moderate
feed motion that is suited to
the material being ma-
chined.
When cutting especially
hard materials such as con-
crete with a high pebble content, the diamond cutting disc
can overheat and become damaged as a result. This is
Bosch Power Tools 1 609 92A 7VN | (31.05.2022)
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWX 17-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 17-125 in the language / languages: All languages as an attachment in your email.

The manual is 22.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info