786296
345
Zoom out
Zoom in
Previous page
1/379
Next page
 | 345
램핑 장치가 불안정해져서 클램핑 공구가 풀릴
수도 있습니다.
uX-LOCK-공구 비트는 별도의 클램핑 및 서포트
플랜지가 필요하지 않습니다.
u공구 비트 및 어댑터가 변형되지 않고 오염 물질
과 미립자가 묻지 않도록 유의하십시오.
연마공구의 치수를 확인하십시오.
X-LOCK-공구 비트를 조립하기 전에 양쪽에 위치한
X-LOCK-고정 러그가 열려 있는지 확인하십시오(다
음 그림 참조).
경우에 따라 양쪽 X-LOCK-고정 러그 사이를 청소하
십시오.
연마 공구 조립하기
연마석/절단석/팬 그라인딩 디스크의 중심을 맞
춰끼우고 접촉면에 나란히 올바른 면이 위쪽을
향하도록 X-LOCK-어댑터에 올리십시오.
어댑터 방향으로 디스크를 누르십시오.
디스크가 맞물려 잠기는 소리가 들려야 합니다.
이때 레버 (3) 를 누르지 마십시오.
(3)
u조립 후 연마 공구의 모서리 ()가 기준면 ()보
다 높지 않은지 정확하게 설치되어 있는지 점검
하십시오. 모서리가 더 높으면, 어댑터를 청소하
거나 연마 공구를 사용해서는 안 됩니다.
연마석/절단석/팬 그라인딩 디스크를 분리하기 전
에: 전동공구가 정지되었는지 확인하십시오.
연마 공구 분리하기
레버 (3) 를 푸십시오.
연마석/절단석/팬 그라인딩 디스크가 풀립니다.
연마석/절단석/팬 그라인딩 디스크를 분리할 수
있습니다.
(3) (3)
허용 연마공구
이 사용 설명서에 나와 있는 모든 연마공구를 사용
할 수 있습니다.
사용된 연마공구의 허용 속도 [min-1]와 원주 속도
[m/s]는 적어도 다음의 도표에 나와 있는 수치와 일
치해야 합니다.
그러므로 항상 사용하는 연마공구의 레벨에 나와 있
허용 속도와 원주 속도를 확인하십시오.
최대 [mm] [mm] [°]
D b s d α [min-1
]
[m/
s]
125 7.2 X-
LOCK
11500 80
125 4.2 X-
LOCK
11500 80
125 X-
LOCK
11500 80
75 30 X-
LOCK
11500 80
125 X-
LOCK
11500 80
125 X-
LOCK
11500 80
82 X-
LOCK
11500 80
α
s
125 6 10 X-
LOCK
> 0 11500 80
기어 헤드 돌리기(그림E참조)
u전동공구를 보수 정비하기 전에 반드시 콘센트에
서 전원 플러그를 빼십시오.
기어 헤드는 90° 간격으로 돌릴 수 있습니다. 특수
한 작업을 할 경우 기어 헤드를 돌려 전원 스위치를
기기 조작이 수월한 위치로 움직일 수 있습니다. 예
를 들면 왼손잡이 작업자에게 유리합니다.
Bosch Power Tools 1 609 92A 6A1 | (14.02.2022)
345


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWX 14-125 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 14-125 S in the language / languages: All languages as an attachment in your email.

The manual is 15.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info