592508
24
Zoom out
Zoom in
Previous page
1/337
Next page
24 | English
3 609 929 B90 | (12.11.09) Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data” is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
11.11.2009
Assembly
Mounting the Protective Devices
f Before any work on the machine itself, pull
the mains plug.
f Operate the machine only with the protec-
tion guard and the bow handle mounted.
Protection Guard for Cutting
f For cutting metal, always work with the pro-
tection guard for cutting 5.
f For cutting stone, always work with the cut-
ting guide with dust extraction protection
guard 17.
Release the clamping lever 7. Place the protec-
tion guard 5 with the encoding key 16 engaging
into the groove on the spindle collar until the
shoulder of the protection guard is seated
against the flange of the power tool, and turn
the protection guard 5 to the requested posi-
tion. Lock the clamping lever 7.
f Adjust the protection guard 5 in such a man-
ner that sparking is prevented in the direc-
tion of the operator.
The tensioning force of the clamping lever is
preset for tight seating of the protection guard
5. By tightening the adjustment screw 6, the ten-
sioning force can be increased. Pay attention to
the tight seating of the protection guard 5 and
check it regularly.
Note: The encoding keys on the protection
guard 5 ensure that only a protection guard that
fits the machine type can be mounted.
Bow Handle
Fasten the bow handle 1 to the gear case as
shown in the figure.
Cutting Guide
The cutting guide 14 prevents the application
tool and the workpiece from jamming.
Loosen the wing nuts on the cutting guide 14.
Press both wing nuts and at the same time in-
sert the screw heads into the slots on the bot-
tom side of the protection guard 5. Adjust the
requested cutting depth and tighten the wing
nuts.
Mounting the Grinding Tools
f Before any work on the machine itself, pull
the mains plug.
f Grinding and cutting discs become very hot
while working; do not touch until they have
cooled.
Note: Use only grinding tools with an outer di-
ameter of maximum 300 mm. For cutting stone
or metal, only use the grinding tools recom-
mended by Bosch.
Clean the grinder spindle 4 and all parts to be
mounted.
For clamping and loosening the grinding tools,
lock the grinder spindle with the spindle lock
button 3.
f Actuate the spindle lock button only when
the grinder spindle is at a standstill. Other-
wise, the machine may become damaged.
Pay attention to the dimensions of the grinding
tools. The mounting hole diameter must fit the
mounting flange without play. Do not use reduc-
ers or adapters.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-280-003.book Page 24 Thursday, November 12, 2009 1:21 PM
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 24-300 PLUS SDS Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 24-300 PLUS SDS Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info