79060

Bosch GWS 21-230 Manual

19
Zoom out
Zoom in
Previous page
1/261
Next page
English - 6
All grinding tools mentioned in this operating
manual instruction can be used.
The permissible speed [rpm] or the circumferen-
tial speed [m/s] of the grinding tools used must at
least match the values given in the table.
Therefore, always observe the permissible
rotational/circumferential speed on the label
of the grinding tool.
Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
To start the machine, press the On/Off switch 3
forward and then down.
To lock-on, push the pressed On/Off switch 3
further forwards.
To switch off the machine, release the On/Off
switch 3 or push and release it then.
Switch version without lock
(country-specific):
To start the machine, press the On/Off switch 3
forward and then down.
To switch off the machine, release the On/Off
switch 3.
☞
Test run!
Check the grinding tool before use. The
grinding tool must be properly mounted
and rotate freely. Perform a test run of at
least 30 seconds without load. Do not use
damaged, out-of-round or vibrating grind-
ing tools.
Reduced Starting Current
(Type J)
As a result of soft starting, a 13 A fuse is
adequate.
A machine without reduced starting current
requires higher fuse protection (use at least
a 13 A time-delay fuse).
■ Clamp the workpiece if it does not remain
stationary due to its own weight.
■ Do not strain the machine so heavily that it
comes to a standstill.
■ Grinding and cutting discs become very
hot while working; do not touch until they
have cooled.
Rough Grinding
The best roughing results are
achieved when setting the machine
at an angle of 30° to 40°. Move the
machine back and forth with mod-
erate pressure. In this manner, the
workpiece will not become too hot,
does not discolour and no grooves
are formed.
Never use a cutting disc for roughing.
Flap Disc
With the flap disc (accessory), curved surfaces
and profiles (contour sanding) can be worked.
Flap discs have a considerably higher service life
than sanding sheets, lower noise level and lower
sanding temperatures.
Approved Grinding Tools
max.
[mm] [mm]
Db d[rpm] [m/s]
180
230
8
8
22.2
22.2
8 500
6 500
80
80
180
230
–
–
–
–
8 500
6 500
80
80
100 30 M 14 8 500 45
Initial Operation
b
d
D
D
D
b
d
Operating Instructions
1 609 929 R35.book Seite 6 Mittwoch, 13. Februar 2008 1:16 13
20 • 1 609 929 R35 • 03.11
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 21-230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 21-230 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info