390388
8
Zoom out
Zoom in
Previous page
1/13
Next page
English - 4
Pay attention to the dimensions of the grinding
disc. The mounting hole diameter must fit the
mounting flange 9 without play. Do not use re-
ducers or adapters.
Never use cutting discs for rough grinding. Do
not exert any lateral pressure on the cutting
discs.
Observe the manufacturer’s instructions for
mounting and using grinding tools.
Caution! The grinding tool runs on after the
machine is switched off.
Do not clamp the machine in a vice.
Never allow children to use the machine.
Bosch is only able to ensure perfect operation
of the machine if the original accessories in-
tended for it are used.
The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting stone, a cutting guide is re-
quired.
Slots in structural walls are subject to the Stand-
ard DIN 1053, Part 1 or country-specific regula-
tions.
These regulations are to be observed under all
circumstances. Before beginning work, consult
the responsible structural engineer, architects or
the construction supervisor.
Before any work on the machine itself, pull
the mains plug.
For work with grinding or cutting discs, the
protection guard 6 must be mounted.
Protection Guard with Locking Screw
The coded projection 14 on the protection
guard 6 ensures that only a guard that fits the
machine type can be mounted.
Loosen the clamping screw 13, if necessary.
Place the protection guard 6 with coded projec-
tion 14 into the coded groove on the spindle col-
lar of the machine head and rotate to the required
position (working position).
The closed side of the protection guard 6
must always point to the operator.
Tighten clamping screw 13.
Protection Guard with Quick Clamp
The protection guard is preadjusted to the
diameter of the spindle collar. If required,
the tightening tension of the clamping
bracket can be changed by tightening or
loosening the adjustment screw 7. Always
ensure that the protection guard 6 is
seated tightly on the spindle collar.
Open the clamping lever 8.
Place the protection guard 6 on the spindle collar
of the machine head and turn to the required po-
sition (working position).
To fasten the protection guard 6, close the
clamping lever 8.
The closed side of the protection guard 6
must always point to the operator.
Auxiliary Handle
For all work with the machine, the auxiliary
handle must be mounted.
Screw the auxiliary handle 4 into the head of the
machine according to the working method.
Do not continue to use an auxiliary handle if it is
damaged.
Hand Guard
For work with the rubber sanding plate 20 or with
the cup brush 23/disc brush/flap disc, the hand
guard 18 (accessory) is to be mounted. The hand
guard 18 is fastened with the auxiliary handle 4.
Intended Use
Information on Structures
Mounting the
Protective Devices
1 609 929 F75.book Seite 4 Dienstag, 9. März 2004 9:19 09
9 • 1 609 929 F75 • 04.03
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch gws 20 180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gws 20 180 in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch gws 20 180

Bosch gws 20 180 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 122 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info