786319

Bosch GWS 17-150 S Manual

30
Zoom out
Zoom in
Previous page
1/437
Next page
30 | English
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
uDo not load the power tool so heavily that it comes to a
stop.
uPull the plug out of the socket before carrying out any
work on the power tool.
uExercise caution when cutting slots in structural walls;
see the "Information on structural design" section.
uClamp the workpiece if it is not secure under its own
weight.
uIf the power tool has been subjected to a heavy load,
continue to run it at no-load for several minutes to
cool down the accessory.
uDo not use the power tool with a cut-off stand.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
Working advice
Rough grinding
uAlways use the protective guard for grinding(9) when
rough grinding with bonded abrasives.
uNever use cutting discs for rough grinding.
uWhen rough grinding, the protective guard for
cutting(10) or the protective guard for grinding(9)
with a fitted cover for cutting(11) can impact the
workpiece and lead to a loss of control.
The best rough grinding results are achieved with a set angle
of 30° to 40°. Move the power tool back and forth with mod-
erate pressure. This will ensure that the workpiece does not
become too hot or discolour and that grooves are not
formed.
uThe protective guard for cutting(10) or the protective
guard for grinding(9) with a fitted cover for cutting(11)
must be used when using bonded discs which are ap-
proved for cutting and grinding.
Surface grinding with flap disc
uAlways use the protective guard for grinding(9) when
grinding with the flap disc.
The flap disc (accessory) enables you to machine curved
surfaces and profiles. Flap discs have a considerably longer
service life, lower noise levels and lower grinding temperat-
ures than conventional grinding discs.
Surface grinding with sanding disc
uAlways fit the hand guard (24) when working with the
rubber sanding pad (25).
Grinding with a sanding disc can be done without a protect-
ive guard.
See the graphics page for fitting instructions.
Screw on the round nut(27) and tighten it with the two-pin
spanner.
Cup brush/disc brush/conical brush
uAlways use the protective guard for grinding(9) when
brushing with disc brushes. Brushing with cup
brushes/conical brushes can be performed without
the protective guard.
uAlways fit the hand guard (24) when working with the
cup brush or conical brush.
uThe wires of the disc brush can get caught on the pro-
tective guard and break, if the maximum permitted di-
mensions of the disc brushes are exceeded.
See the graphics page for fitting instructions.
The cup brush/conical brush/disc brush with M14 thread
must be screwed onto the grinding spindle until it rests
firmly against the grinding spindle flange at the end of the
grinding spindle thread. Tighten the cup brush/conical
brush/disc brush with an open-ended spanner.
To fasten the disc brush with a diameter of 22.22mm, at-
tach the mounting flange with O-ring(12) to the grinding
spindle(23), screw on the round nut(27) and tighten with
the two-pin spanner.
Cutting Metal
uFor cutting metal with bonded cutting discs or dia-
mond cutting discs, always use the protective guard
for cutting(10) or the protective guard for
grinding(9) with a fitted cover for cutting(11).
uWhen using the protective guard for grinding(9) for
cutting work with bonded cutting discs, there is an in-
creased risk of being exposed to sparks, particles and
disc fragments if the disc breaks.
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
1 609 92A 6A0 | (11.02.2022) Bosch Power Tools
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 17-150 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 17-150 S in the language / languages: All languages as an attachment in your email.

The manual is 16.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info