786313
26
Zoom out
Zoom in
Previous page
1/437
Next page
26 | English
GWS 14-125 GWS 14-125 S GWS 17-125 GWS 17-125 S
ah
K
m/s2
m/s2
3.2
1.5
3.2
1.5
< 2.5
1.5
< 2.5
1.5
GWS 17-125 TS GWS 17-125 S INOX GWS 17-150 S
3601GD04.. 3601GD05.. 3601GD06..
Noise emission values determined according toENIEC62841-2-3.
Typically, the A-weighted noise level of the power tool is
Sound pressure level
Sound power level
UncertaintyK
Wear hearing protection!
dB(A)
dB(A)
dB
94
102
3
95
103
3
95
103
3
Vibration total values ah (triax vector sum) and uncertainty K determined according toENIEC62841-2-3:
Surface grinding and abrasive cutting:
ah
K
m/s2
m/s2
5.5
1.5
5.4
1.5
8.0
1.5
Disc sanding:
ah
K
m/s2
m/s2
3.1
1.5
2.5
1.5
3.5A)
1.5
A) Determined for a diameter of 125mm
Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission
value to increase by up to 15dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise
emissions must be taken into consideration, both for the risk assessment of the noise output and for selecting suitable hearing
protection.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Restart protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (3) to the off posi-
tion and then switch the power tool on again.
Starting current limitation
The electronic starting current limitation feature restricts the
power of the power tool when it is switched on and enables
operation using a 16 A fuse.
Note: If the power tool runs at full speed immediately after
being switched on, this means that the starting current limit-
ation and restarting protection mechanisms have failed. The
power tool must be sent to the after-sales service immedi-
ately; see the "After-Sales Service and Application Service"
section for addresses.
Constant Electronic control
The Constant Electronic keeps the speed at no load and un-
der load virtually consistent, guaranteeing uniform perform-
ance.
Kickback control
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
1 609 92A 6A0 | (11.02.2022) Bosch Power Tools
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 14-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 14-125 in the language / languages: All languages as an attachment in your email.

The manual is 16.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info