79069

Bosch GWS 14-125 CIE Manual

25
Zoom out
Zoom in
Previous page
1/199
Next page
26 | English
1 609 929 L00 | (25.7.08) Bosch Power Tools
f Never place your hand near the rotating ac-
cessory. Accessory may kickback over your
hand.
f Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction op-
posite to the wheel’s movement at the point
of snagging.
f Use special care when working corners,
sharp edges, etc. Avoid bouncing and snag-
ging the accessory. Corners, sharp edges or
bouncing have a tendency to snag the rotat-
ing accessory and cause loss of control or
kickback.
f Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control
over the power tool.
Additional safety instructions for grind-
ing and cutting off operations
f Use only wheel types that are recommend-
ed for your power tool and the specific
guard designed for the selected wheel.
Wheels for which the power tool was not de-
signed cannot be adequately guarded and
are unsafe.
f The guard must be securely attached to the
power tool and positioned for maximum
safety, so the least amount of wheel is ex-
posed towards the operator. The guard
helps to protect operator from broken wheel
fragments and accidental contact with
wheel.
f Wheels must be used only for recommend-
ed applications. For example: do not grind
with the side of the cut-off wheel. Abrasive
cut-off wheels are intended for peripheral
grinding; side forces applied to these wheels
may cause them to shatter.
f Always use undamaged wheel flanges that
are of correct size and shape for your se-
lected wheel. Proper wheel flanges support
the wheel thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels
may be different from grinding wheel flanges.
f Do not use worn down wheels from larger
power tools. Wheels intended for larger
power tools are not suitable for the higher
speed of a smaller tool and may burst.
Additional safety warnings specific for
abrasive cutting off operations
f Do not “jam” the cut-off wheel or apply ex-
cessive pressure. Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibili-
ty to twisting or binding of the wheel in the
cut and the possibility of kickback or wheel
breakage.
f Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away
from your body, the possible kickback may
propel the spinning wheel and the power
tool directly at you.
f When wheel is binding or when interrupting
a cut for any reason, switch off the power
tool and hold the power tool motionless un-
til the wheel comes to a complete stop. Nev-
er attempt to remove the cut-off wheel from
the cut while the wheel is in motion other-
wise kickback may occur. Investigate and
take corrective action to eliminate the cause
of wheel binding.
f Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully reenter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
f Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag un-
der their own weight. Supports must be
placed under the workpiece near the line of
cut and near the edge of the workpiece on
both sides of the wheel.
f Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can
cause kickback.
OBJ_BUCH-340-002.book Page 26 Friday, July 25, 2008 9:21 AM
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 14-125 CIE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 14-125 CIE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GWS 14-125 CIE

Bosch GWS 14-125 CIE User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 199 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info