786323

Bosch GWS 11-125 P Manual

26
Zoom out
Zoom in
Previous page
1/395
Next page
26 | English
Hand guard
uAlways fit the hand guard (21) when working with the
rubber sanding pad (22) or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard(21) to the auxiliary handle(6)/(32).
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle (6)/(32) on the right or left of the
machine head depending on the working method.
uDo not operate your power tool without the auxiliary
handle(6)/(32).
uDo not continue to use the power tool if the auxiliary
handle (6)/(32) is damaged. Do not make any altera-
tions to the auxiliary handle (6)/(32).
The low-vibration auxiliary
handle (32) reduces vibra-
tion, enabling the tool to be
used safely and more com-
fortably.
Fitting the Abrasive Tools
uPull the plug out of the socket before carrying out any
work on the power tool.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
Clean the grinding spindle (18) and all the parts to be fitted.
Lock the grinding spindle with the spindle lock button (2)
before clamping and releasing the abrasive tools.
uDo not press the spindle lock button while the grind-
ing spindle is moving. The power tool may become dam-
aged if you do this.
Grinding/cutting disc
Pay attention to the dimensions of the abrasive tools. The
diameter of the hole must match that of the mounting flange.
Do not use an adapter or reducer.
When using diamond cutting discs, make sure that the direc-
tion of rotation arrow on the diamond cutting disc corres-
ponds to the direction of rotation of the machine (see direc-
tion of rotation arrow on the housing).
See the graphics page for fitting instructions.
Note: When assembling bonded grinding or cutting discs us-
ing the supplied mounting flange(10) and the clamping
nut(15) or quick-clamping nut(16), the use of intermediate
layers is not necessary.
To secure the grinding/cutting disc, place the mounting
flange with O-ring(10) on the grinding spindle(18) and
screw on the clamping nut(15). Pay attention to the align-
ment of the clamping nut(15) depending on the grinding/
cutting disc that is being used (see figures at the beginning
of the.operating manual), and tighten it with the two-pin
spanner (see " Quick-clamping nut ",
page26).
uAfter fitting the abrasive tool, check that the abrasive
tool is fitted correctly and can turn freely before
switching on the power tool. Make sure that the abras-
ive tool does not brush against the protective guard or
other parts.
A plastic part (O-ring) is fitted around the cent-
ring collar in the mounting flange (10). If the
O-ring is missing or damaged, the mounting
flange (10) must be replaced before operation
can resume.
Quick-clamping nut
To change the abrasive tool easily without having to use any
additional tools, you can use the quick-clamping nut (16) in-
stead of the clamping nut (15).
uThe quick-clamping nut (16) may be used only for
grinding or cutting discs.
Only use quick-clamping nuts (16) that are in good work-
ing order and not damaged.
When screwing on, make sure that the printed side of the
quick-clamping nut (16) is not facing the grinding disc;
the arrow must be pointing towards the index mark (33).
(33)
Press the spindle lock but-
ton (2) to lock the grinding
spindle. To tighten the
quick-clamping nut, turn
the grinding disc firmly
clockwise.
If the quick-clamping nut
has been attached correctly
and is not damaged, you
can loosen it by hand by
turning the knurled ring an-
ticlockwise. If the quick-
clamping nut is stuck, do
not attempt to loosen it
with pliers – always use
the two-pin spanner. Posi-
tion the two‑pin spanner as
shown in the figure.
Approved abrasive tools
You can use all the abrasive tools mentioned in these operat-
ing instructions.
The permissible speed [min-1] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
1 609 92A 7AL | (30.03.2022) Bosch Power Tools
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 11-125 P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 11-125 P in the language / languages: All languages as an attachment in your email.

The manual is 18.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info