78611
34
Zoom out
Zoom in
Previous page
1/199
Next page
English | 35
Bosch Power Tools 1 609 929 L00 | (25.7.08)
Cutting Metal
f For cutting metal, always work with the pro-
tection guard for cutting 13.
When cutting, work with moderate feed, adapt-
ed to the material being cut. Do not exert pres-
sure onto the cutting disc, tilt or oscillate the
machine.
Do not reduce the speed of running down cut-
ting discs by applying sideward pressure.
The machine must
always work in an
up-grinding mo-
tion. Otherwise,
the danger exists
of it being pushed
uncontrolled out
of the cut.
When cutting pro-
files and square
bar, it is best to
start at the small-
est cross section.
Cutting Stone
f For cutting stone, always work with the cut-
ting guide with dust extraction protection
guard 20.
f The machine may be used only for dry cut-
ting/grinding.
For cutting stone, it is best to use a diamond
cutting disc. As a safety measure against jam-
ming, the cutting guide with dust extraction pro-
tection guard 20 must be used.
Operate the machine only with dust extraction
and additionally wear a dust protection mask.
The vacuum cleaner must be approved for the
extraction of masonry dust. Bosch provides suit-
able vacuum cleaners.
Switch on the ma-
chine and place
the front part of
the cutting guide
on the workpiece.
Slide the machine
with moderate
feed, adapted to
the material to be
worked.
For cutting expecially hard material, e. g., con-
crete with high pebble content, the diamond
cutting disc can overheat and become damaged
as a result. This is clearly indicated by circular
sparking, rotating with the diamond cutting
disc.
In this case, interrupt the cutting process and al-
low the diamond cutting disc to cool by running
the machine for a short time at maximum speed
with no load.
Noticeable decreasing work progress and circu-
lar sparking are indications of a diamond cutting
disc that has become dull. Briefly cutting into
abrasive material (e. g. lime-sand brick) can re-
sharpen the disc again.
Information on Structures
Slots in structural walls are subject to the
Standard DIN 1053 Part 1, or country-specific
regulations.
These regulations are to be observed under all
circumstances. Before beginning work, consult
the responsible structural engineer, architect or
the construction supervisor.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
f In extreme working conditions, conductive
dust can accumulate in the interior of the
machine when working with metal. The pro-
tective insulation of the machine can be de-
graded. The use of a stationary extraction
system is recommended in such cases as
well as frequently blowing out the ventila-
tion slots and installing a residual current
device (RCD).
OBJ_BUCH-340-002.book Page 35 Friday, July 25, 2008 9:21 AM
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 10-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 10-125 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info