386456
19
Zoom out
Zoom in
Previous page
1/107
Next page
English | 19
Bosch Power Tools 1 609 929 R97 | (11.6.08)
Setting the Torque
With the torque selector switch 6, you can prese-
lect the required torque in 8 steps. When the
torque setting is adjusted correctly, the insert
tool is stopped as soon as the screw is driven
flush into the material or when the set torque is
reached. In the “ ” position, the safety clutch is
deactivated; e.g., for drilling.
In left rotation the safety clutch is deactivated.
Switching On and Off
To start the machine, press the On/Off switch 5
and keep it pressed.
To switch off the machine, release the On/Off
switch 5.
Adjusting the Speed
The speed of the switched on power tool can be
variably adjusted, depending on how far the
On/Off switch 5 is pressed.
Light pressure on the On/Off switch 5 results in
a low rotational speed. Further pressure on the
switch results in an increase in speed.
Fully automatic spindle locking (Auto-lock)
When the On/Off switch 5 is not pressed, the
drill spindle and thus the tool holder are locked.
This enables screws to be screwed in, even when
the battery is empty and allows for the machine
to be used as a screwdriver.
Temperature Dependent Overload Protection
When using as intended for, the power tool can-
not be subject to overload. When the load is too
high or the allowable battery temperature of
70 °C is exceeded, the electronic control switch-
es off the power tool until the temperature is in
the optimum temperature range again.
Protection Against Deep Discharging
The Li-ion battery is protected against deep dis-
charging by the “Electronic Cell Protection
(ECP)”. When the battery is empty, the machine
is switched off by means of a protective circuit:
The inserted tool no longer rotates.
Angle Selection of Drill Head (see figure D)
The drill head can be locked in 5 different angle
positions. Push the release button 7 and swivel
the tool head to the required position. Then, let
go of the release button 7 again.
f Before starting operation, check if the drill
head is locked in the respective angle posi-
tion. Danger of injury.
Working Advice
f Apply the power tool to the screw only when
it is switched off. Rotating tool inserts can
slip off.
Utility Clip
The swivelling utility clip 8 can be used to hang
the power tool onto a hook. In this manner, both
hands are free and the power tool is ready to
hand.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the power tool, remove
the battery.
f For safe and proper working, always keep
the machine and ventilation slots clean.
When the battery is no longer operative, please
refer to an authorised after-sales service agent
for Bosch power tools.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article number
given on the type plate of the machine.
OBJ_BUCH-134-006.book Page 19 Wednesday, June 11, 2008 2:39 PM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch gwi 10 8v-li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gwi 10 8v-li in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info