786107
13
Zoom out
Zoom in
Previous page
1/175
Next page
English | 13
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Removing the Battery (seefigureA)
To remove the battery(6), press the battery release
buttons(7) and pull the battery out of the power tool. Do
not use force to do this.
Battery charge indicator
The three green LEDs on the battery charge indicator(9) in-
dicate the state of charge of the battery(6). For safety reas-
ons, it is only possible to check the state of charge when the
power tool is not in operation.
To display the state of charge, press and hold the battery
charge indicator button(8) when the power tool is switched
off.
LEDs Capacity
3× continuous green light ≥66%
2× continuous green light ≥33%
1× continuous green light <33%
1× flashing green light Reserve
Changing the Tool (seefiguresB1−B2)
uBefore removing, allow the blade to cool down. The
blade can become warm during operation.
Loosen the knurled screw(1) and push the protective
guard(3) all the way to the top.
Use a screwdriver to turn the blade(10) until a hole
opens in the blade.
Insert a thin, stable object (e.g. a nail) in the open hole in
order to block the blade.
Undo the screw for securing the blade(11) in rotational
direction.
Remove the object used to block the blade.
Lift the blade(10) slightly and pull it down and out.
Place the blade on the tool holder with the ground edge
facing outwards. Ensure that the blade clicks into place in
the tool holder.
Retighten the screw for securing the blade(11) in rota-
tional direction .
Adjust the protective guard(3) to the material thickness
to be cut and tighten the knurled screw(1).
Adjusting the Protective Guard
uNever use the power tool without the protective
guard.
To protect your fingers from injuries, the protective
guard(3) must be adjusted to the material thickness being
cut before each work step.
To do this, loosen the knurled screw(1). Adjust the protect-
ive guard(3) (in the range 2−11mm) so that it loosely rests
against the material to be cut. Retighten the knurled screw.
Adjust the protective guard(3) to the bottom position after
each use as well as before all work on the power tool.
Operation
Starting Operation
Inserting the Battery
Insert the charged battery(6) into the battery receptacle,
making sure you feel it engage and that it is securely locked
in place.
Switching On and Off
To switch on the power tool, slide the on/off switch(4) for-
wards so that I appears on the switch.
Bosch Power Tools 1 609 92A 7ST | (18.05.2022)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GUS 12V-300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GUS 12V-300 in the language / languages: All languages as an attachment in your email.

The manual is 4.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info