426991
10
Zoom out
Zoom in
Previous page
1/68
Next page
12
Euro • BA 3 609 929 301 • GUF 4-22 A • OSW 11/00 • GB
For long hair, wear hair protection. Work only
with close-fitting clothes.
Persons under 16 years of age are not permit-
ted to operate this machine.
Bosch can assure flawless functioning of the
machine only when original accessories are
used.
The machine should be switched on only when
in the initial position, i. e. when the cutting disc is
swung into the base plate.
Switching On/Off
Switching on: Press the on/off switch 19 for-
ward.
Switching off: Unlock the on/off switch 19 by
pressing.
Always use the correct supply voltage: The
voltage of the power source must agree with the
value given on the nameplate of the machine.
Machines designated for 230 V can also be oper-
ated with 220 V.
Cutting Depth Selection
The cutting depth is set with the scale 6.
Left hand side: Biscuit cuts with mounted angle
guide 10.
Right hand side: Cutting without angle
guide 10.
The coarse adjustment is made by pressing the
button 7 and sliding the knurled knob 5.
The fine adjustment is made by turning the
knurled knob 5.
Parallel Guide
The parallel guide 2 serves for cutting parallel to
the edge of a workpiece. It is possible to mount
the parallel guide 2 reversed, if required. It is set
with the clamping lever 16.
Angle guide
The machine is shipped with mounted angle
guide 10. To remove the angle guide, please re-
move the two screws 11.
Biscuit cuts must be made with mounted angle
guide 10.
The angle is set with the scale 8 by loosening
the wing nuts 9 and 24.
The machine is always to be guided with both
hands (shadow gap cutting, Fig. E; Groove
cutting, Fig. F).
Cutting Direction
The cutting must always be opposite to the rota-
tional direction of the cutter (opposed rotation).
When cutting in the direction of rotation, the
machine can be jerked out of the hands of the
operator.
Cutting mark
The mark 3 indicates the cutting mark for the ful-
ly plunged cutting disk. The right res. the left
mark shows the maximum cutting depth.
Shadow Gap
For the mounting of profile boards or panels, the
first and the last must be fitted exactly. The ma-
chine cannot go completely into the corner (cor-
ner distance a=80 mm).
The machine is intended for making grooved
joints and for cutting the edges of wall and ceil-
ing panelling (shadow gap).
Intended use
Before use
Initial operation
Operating instructions
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch guf 4 22a at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch guf 4 22a in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info