Manual Bosch GSR 18V-110 C (page 19 of 257) (All languages)

786162

Zoom out

Zoom in

1/257

English | 19

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (16) to the middle posi-

tion to avoid unintentionally switching it on. Insert the

charged battery (11) into the handle until you feel it engage

and it is flush with the handle.

Setting the rotational direction (see figure B)

The rotational direction switch (16) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (17) is being pressed.

Rotate clockwise: Slide the rotational direction

switch (16) on both sides until it stops in the posi-

tion.

Rotate anti-clockwise: Slide the rotational direction

switch (16) on both sides until it stops in the posi-

tion.

Setting the operating mode

Drilling

Set the mode selector switch(8) to the

"drilling" symbol.

Screwdriving

Set the mode selector switch(8) to the "screw-

driving" symbol.

Impact drilling(GSB 18V-110 C)

Set the mode selector switch(8) to the "impact

drilling" symbol.

Switching on/off

To start the power tool, press and hold the on/off switch

(17).

The LED (13) lights up when the on/off switch (17) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (17).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (17) to varying extents.

A light pressure on the on/off switch (17) results in a low ro-

tational speed. Increased pressure on the switch causes an

increase in speed.

Preselecting torque (applies to screwdriving mode)

The torque presetting ring (7) can be used to preselect the

required torque in 25 stages. Once the set torque has been

reached, the application tool will be stopped.

Mechanical gear selection

uOnly operate the gear selector (9) when the power

tool is not in use.

First gear:

Low speed range; for working with a large drilling diameter

or for screwdriving.

Second gear:

High speed range; for working with a small drilling diameter.

uAlways push the gear selector switch as far as it will

go. Otherwise, the power tool may become damaged.

Temperature-dependent overload protection

When used as intended, the power tool cannot be over-

loaded. In the event of overloading or the temperature

rising/falling outside the permitted operating temperature

range, the speed will be reduced. The power tool will not run

at full speed again until the permitted operating temperature

has been reached.

Activation of the temperature-controlled overload protector

is indicated by the LED (14) on the power tool lighting up

red. To return to within the permitted operating temperature

range, switch the gear selector (9) to first gear, run the

power tool at no load or wait until the LED (14) goes out.

When the LED (14) has gone out, the tool has returned to

within the permitted operating temperature range.

Emergency switch-off (KickBack Control)

The rapid shut-off function (KickBack Con-

trol) gives the user greater control over the

power tool and offers them better protec-

tion than power tools that do not have Kick-

Back Control. The power tool will switch off if it suddenly

and unforeseeably rotates around the drilling axis.

Rapid shut-off is indicated by the LED on the power tool

flashing.

To switch the tool back on, release the on/off switch and

then press it again.

uIt will no longer be possible to switch the power tool

on if the KickBack Control function is faulty. Have the

power tool serviced by a qualified repair person using

only original replacement parts.

Bosch Power Tools 1 609 92A 837 | (14.07.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSR 18V-110 C in the language / languages: All languages as an attachment in your email.

The manual is 5.6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSR 18V-110 C Manual

Product: