544118
14
Zoom out
Zoom in
Previous page
1/154
Next page
14 | English
2 609 141 014 | (3.5.13) Bosch Power Tools
Switching On and Off
To start the machine, press the On/Off switch 7 and keep it
pressed.
The LED 12 lights up when the On/Off switch 7 is halfway or
fully pressed, and enables illumination of the screwing loca-
tion in unfavourable light conditions.
To lock the pressed On/Off switch 7, press the lock-on button
6.
To switch off the machine, release the On/Off switch 7 or
when it is locked with the lock-on button 6, briefly press the
On/Off switch 7 and then release it.
To save energy, only switch the power tool on when using it.
Adjusting the Speed
The speed of the switched on power tool can be variably ad-
justed, depending on how far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in a low rotation-
al speed. Further pressure on the switch results in an increase
in speed.
Adjusting the Screw-in Depth (see figure B)
With the adjustment sleeve 3, the screw-in depth of the screw
head into the workpiece can be preset in 8 locking steps per
full turn. Each step corresponds with a 0.25 mm change of
the screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction results
in a greater screw-in depth; turning in anticlockwise direction
reduces the screw-in depth.
The required setting is best determined by testing.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature range of 070 °C is exceeded, the speed is re-
duced. The power tool will not run at full speed until reaching
the allowable battery temperature.
Protection Against Deep Discharging
The Lithium-Ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Working Advice
Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
Guide the screw toward the screwdriving bit 1. The screw is
held in place by the magnet pull of the universal bit holder 13.
Firmly push the tip of the screw into the material to be
screwed until the screwing-depth stop 4 faces against the
workpiece.
Switch the machine on. The screw is screwed into the materi-
al until the adjusted screw-in depth is reached. The drive is
disengaged and the tool holder no longer rotates. Check the
screw-in depth and readjust, if required.
For unscrewing screws, set the rotational direction switch 5
to left rotation and pull off the screwing-depth stop 4 toward
the front without turning the adjustment sleeve.
Working with the screwing-depth stop 4 is also possible when
adapting the screw-in depth.
Belt Clip
With the belt clip 8, the machine can be hung onto a belt. The
user has both hands free and the machine is always at hand.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
OBJ_BUCH-1908-001.book Page 14 Friday, May 3, 2013 12:30 PM
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSR 18 V-EC TE plus MA 55 Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSR 18 V-EC TE plus MA 55 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info