Manual Bosch gsr 12 0 1 (page 24 of 30) (English, Danish, Swedish, Norwegian, Finnish)

387122

Zoom out

Zoom in

1/30

English

⅜ Should the saw blade be stopped or made an

abnormal noise during operation, turn off the switch

immediately.

⅜ Always take care in preventing the power cord from

coming near the revolving saw blade.

MOUNTING AND DISMOUNTING THE SAW

BLADE

CAUTION

To avoid serious accident, ensure the switch is in the

OFF position, and the power source is disconnected.

1. Dismounting the saw blade

(1) Set the cutting volume at maximum, and place the

Circular Saw as shown in Fig. 8.

(2) Depress the lock lever, lock the spindle, and remove

the hexagonal-head bolt with the box wrench.

(3) While holding the safety cover lever to keep the

safety cover fully retracted into the saw cover,

remove the saw blade.

2. Mounting the Saw Blade:

(1)Thoroughly remove any sawdust which has

accumulated on the spindle, bolt and washers.

(2) As shown in Fig. 9, the side of Washer (A) with

a projected center the same diameter as the inner

diameter of the saw blade and the concave side

of Washer (B) must be fitted to the saw blade sides.

*Washer (A) is supplied for 3 types of saw blades

with the hole diameters of 16 mm, 20 mm and

30 mm. (When buying the Circular Saw, one

type of washer (A) is spplied.)

In case the hole diameter of your saw blade

does not correspond to that of washer (A), please

contact the shop where you purchased the

Circular Saw.

(3) To assure proper rotation direction of the saw blade,

the arrow direction on the saw blade must coincide

with the arrow direction on the saw cover.

(4) Using the fingers, tighten the hexagonal-head bolt

retaining the saw blade as much as possible. Then

depress the lock lever, lock the spindle, and

thoroughly tighten the bolt.

CAUTION

After having attached the saw blade, reconfirm that the

lock lever is firmly secured in the prescribed position.

MAINTENANCE AND INSPECTION

1. Inspecting the saw blade:

Since use of a dull saw blade will degrade efficiency

and cause possible motor malfunction, sharpen or

replace the saw blade as soon as abrasion is noted.

2. Inspecting the mounting screws:

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Inspecting the carbon brushes (Fig. 10)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush can result in motor trouble, replace the carbon

brushes with new ones having the same carbon

brush No. shown in the figure when it becomes

worn to or near the “wear limit”. In addition, always

keep carbon brushes clean and ensue that they

slide freely within the brush holders.

4. Replacing carbon brushes:

Disassemble the brush caps with a slotted-head

screwdriver. The carbon brushes can then be easily

removed.

5. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

6. Adjusting the base and saw blade to maintain

perpendicularity:

The angle between the base and the saw blade has

been adjusted to 90°, however should this

perpendicularity be lost for some reason, adjust in

the following manner:

(1) Turn the base face up (Fig. 11) and loosen the knob

and wing-bolt (Fig. 5 (A), Fig. 5 (B)).

(2) Apply a square to the base and the saw blade and

turning the slotted set screw with a slotted-head

screwdriver, shift the position of the base to produce

the desired right angle.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to

EN50144.

The typical A-weighted sound pressure level: 97 dB (A)

The typical A-weighted sound power level: 110 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration value

does not exceed 2.5 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gsr 12 0 1 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gsr 12 0 1 Manual

Product: