Manual Bosch GSN 90-34 DK Professional (page 14 of 160) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

594782

Zoom out

Zoom in

1/160

1 609 92A 10Z | (10.11.14) Bosch Power Tools

14 | English

Declaration of Conformity

We declare under our sole responsibility that the product

described under “Technical data” complies with all applica-

ble provisions of the directive 2006/42/EC including its

amendments and is in conformity with the following stand-

ards: EN 792-13.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 12.11.2014

Assembly

Connecting the Air Supply (see figure A)

Make sure that the pressure of the compressed-air system

is below the maximum permitted rated pressure of the

pneumatic tool. Firstly, set the air pressure to the lower

value of the recommended rated pressure (see “Technical

Data”).

When in doubt, check the pressure at the air inlet with a

pressure gauge with the pneumatic tool switched on.

For maximum performance, the values for the supply-air

hose 13 (connection thread, maximum operating pres-

sure, inner hose diameter, maximum hose length; see

“Technical Data”) must be observed.

The compressed air supplied should be free of foreign ma-

terial and moisture to protect the tool from damage, con-

tamination, and the formation of rust.

All fittings, connecting lines and hoses must be dimen-

sioned for the pressure and the required air volume.

Avoid restrictions in the air supply, e.g., from pinching,

kinking, or stretching!

Connecting the Air Supply to the Pneumatic Tool

– Empty the magazine 8.

(See “Emptying the Magazine”, page 14)

For the following worksteps, a fastener can be dis-

charged when interior parts of the pneumatic tool are

not in the starting position due to repairs, maintenance

or transport.

– Connect the air connector 6 with a supply-air hose 13

equipped with an air-connection coupling 12.

– Check the proper function by placing the outlet 11 or

the rubber workpiece protector 1 of the pneumatic tool

onto a piece of scrap wood or wood material, and dis-

charging once or twice.

Loading the Magazine (see figures B1–B2)

Disconnect the air supply before making

any adjustments, changing accessories,

or placing the pneumatic tool aside. This

safety measure prevents accidental start-

ing of the pneumatic tool.

 Use only original Bosch accessories (see “Technical

Data”). The precision parts of the pneumatic tool such

as the magazine, the outlet and the shot duct are

matched to Bosch staples, nails and brads. Other man-

ufacturers use other steel qualities and sizes.

Using fasteners not permitted, can damage the pneu-

matic tool and cause injuries.

While loading the magazine, hold the pneumatic tool in

such a manner that the outlet 11 is not pointed at your own

body or at other persons.

– Pull back the magazine slider 7 until it engages at the

rear.

Note: The magazine slider must slide back with only low

force (finger-pressure). A tight-running magazine slider

causes the nails to be driven in at an incorrect angle.

– Clean and lubricate the magazine slider 7 as required

and make sure that the magazine 8 is not dirty/soiled.

– Insert a fitting nail strip 14.

Do not use nail strips with less than 5 nails. Do not insert

more than 2 nail strips. Make sure that the heads of the

nails do not overlap.

GSN 90-34 DK: With this pneumatic tool, a lock function

of the magazine slider prevents the last nails from being

discharged. Approx. 7 nails remain in the magazine.

– Completely pull back the magazine slider 7 once more

to free the lock.

– Carefully guide the magazine slider to the front until it

touches the nail strip.

Make sure that the magazine slider is slid beyond the

head of the last nail.

Note: Do not let the magazine slider snap back without

guiding it. Otherwise, the magazine slider could become

damaged, and there is danger of your fingers being caught

or pinched.

Operation

Actuation systems

The pneumatic tool can be operated with two different ac-

tuations systems:

– Single actuation with safety run

With this actuation system, the discharge lock-off 2

must first be firmly pressed against the workpiece. A

fastener is not discharged until the trigger 10 is pulled.

Afterwards, further discharging procedures can only be

actuated, when the trigger and the discharge lock-off

have first been set back to the starting position.

– Contact actuation

With this actuation system, the trigger 10 must be

pulled first. A fastener is always discharged when the

discharge lock-off 2 is firmly pressed against the work-

piece while the trigger is pressed.

This enables a higher working speed to be achieved.

The actuation system is set via the selector switch 9.

Starting Operation

Disconnect the air supply before making

any adjustments, changing accessories,

or placing the pneumatic tool aside. This

safety measure prevents accidental start-

ing of the pneumatic tool.

Working with Single Actuation (see figure C)

– Press selector switch 9 inward and at the same time piv-

ot it to the bottom position until it engages.

The actuation system “single

actuation” is set.

– Release the selector switch 9 again.

– Firmly position the outlet 11 or the rubber workpiece

protector 1 on the workpiece until discharge lock-off 2

is pressed in completely.

– Afterwards, briefly press trigger 10 and release again.

A nail is discharged.

– Allow the pneumatic tool to bounce back from the work-

piece.

– For another driving procedure, completely lift the pneu-

matic tool from the workpiece and position it firmly at

the next desired location.

Working with Contact Actuation (see figure D)

– Press selector switch 9 inward and at the same time piv-

ot it to the upper position until it engages.

The actuation system

“contact actuation” is

set.

– Release the selector switch 9 again.

– Press and hold the trigger 10.

– Firmly position the outlet 11 or the rubber workpiece

protector 1 on the workpiece until discharge lock-off 2

is pressed in completely.

A nail is discharged.

– Allow the pneumatic tool to bounce back from the work-

piece.

– For another driving procedure, completely lift the pneu-

matic tool from the workpiece and position it firmly at

the next desired location.

– Move the pneumatic tool uniformly over the workpiece

by lifting it off and applying it again.

Each time when applying the pneumatic tool while the

discharge lock-off is pressed in, a nail will be dis-

charged.

– As soon as the desired amount of nails have been driven

in, release trigger 10 again.

Working Advice

Disconnect the air supply before making

any adjustments, changing accessories,

or placing the pneumatic tool aside. This

safety measure prevents accidental start-

ing of the pneumatic tool.

Check the proper function of the safety and actuation de-

vices, and the tight seating of all screws and nuts each time

before using.

Disconnect a defective or not properly operating pneumat-

ic tool immediately from of the air supply and contact an

authorised service agent for Bosch power tools.

Do not perform any incorrect manipulations on the pneu-

matic tool. Do not disassemble or block any components of

the pneumatic tool, such as the discharge lock-off.

Do not carry out “emergency repairs” with unsuitable

means. The pneumatic tool is to be maintained regularly

and properly (see “Maintenance and Cleaning”, page 15).

Avoid any weakening and damage whatsoever of the pneu-

matic tool, e.g., through:

– Imprinting or engraving,

– Retrofitting measures not approved by the manufactur-

er,

– Guiding along templates manufactured of hard material,

e.g. steel,

– Dropping on or sliding over the floor,

– Using as a hammer,

–Applying any kind of force.

Make sure to check whatever is below or behind your work-

piece. Do not shoot nails into walls, ceilings or floors, when

persons are behind them. The nails can burst through the

workpiece and injure someone.

Do not shoot a nail onto an already driven-in one. This

could cause the nail to deform, the nails could become

jammed or the pneumatic tool could move uncontrolled.

When the pneumatic tool is used under cold ambient con-

ditions, the first nails will be driven in slower than usual.

Once the pneumatic tool has warmed up during working,

normal operating speed will be regained.

Avoid blank shots in order to reduce the wear of the impact

striker.

For longer work breaks or after finishing work, disconnect

the pneumatic tool from the air supply and empty the mag-

azine.

Emptying the Magazine

– Pull back the magazine slider 7 until it engages at the

rear.

– Remove the nail strips 14.

Discard nail strips with less than 5 nails.

– Completely pull back the magazine slider 7 once more

to free the lock.

– Carefully guide the magazine slider to the front until it

touches the beginning of the magazine.

Note: Do not let the magazine slider snap back without

guiding it. Otherwise, the magazine slider could become

damaged, and there is danger of your fingers being caught

or pinched.

Adjusting the Depth Stop (see figure E)

The driving depth of the nails can be set with thumbwheel

– Empty the magazine 8.

(See “Emptying the Magazine”, page 14)

– Nails are driven in too deeply:

To reduce the driving depth, turn thumbwheel 3 in

clockwise direction.

Nails are not driven in deep enough:

To increase the driving depth, turn thumbwheel 3 in an-

ticlockwise direction.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

OBJ_BUCH-1037-005.book Page 14 Monday, November 10, 2014 12:55 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSN 90-34 DK Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSN 90-34 DK Professional Manual

Product: