594781
16
Zoom out
Zoom in
Previous page
1/160
Next page
1 609 92A 10Z | (10.11.14) Bosch Power Tools
16 | English
Accessories
For more information on the complete quality accessories
program, please refer to the Internet under
www.bosch-pt.com or contact your specialist shop.
After-sales Service and Application Service
Our after-sales service responds to your questions con-
cerning maintenance and repair of your product as well as
spare parts. Exploded views and information on spare
parts can also be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer ques-
tions concerning our products and their accessories.
In all correspondence and spare parts orders, please al-
ways include the 10-digit article number given on the type
plate of the pneumatic tool.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or ar-
range the collection of a product in need of servicing or re-
pair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
The nails are discharged very slowly and with too little pres-
sure.
The rated pressure of the compressed-air supply is too low. Increase the compressed-air supply. 8 bar may not be
exceeded.
The driver blade is damaged. Use only the lubricants recommended by Bosch.
(See “Lubricating the Pneumatic Tool”, page 15)
The sealing ring of the piston is worn or damaged. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The buffer is worn. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The length and diameter of supply-air hose 13 do not corre-
spond with the data of this pneumatic tool.
Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 13)
The supply-air hose 13 is bent/creased. Correct the bend/crease in the supply-air hose.
The nails are driven in too deep.
The rated pressure of the compressed-air supply is too high. Reduce the compressed-air supply. 5 bar may not be
fallen below.
The depth stop is set too deep. Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 14)
The buffer is worn. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The nails are not driven in deep enough.
The rated pressure of the compressed-air supply is too low. Increase the compressed-air supply. 8 bar may not be
exceeded.
The depth stop is set too high. Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 14)
The length and diameter of supply-air hose 13 do not corre-
spond with the data of this pneumatic tool.
Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 13)
The supply-air hose 13 is bent/creased. Correct the bend/crease in the supply-air hose.
The pneumatic tool skips nails or has a too large cycle feed.
The fasteners being used are not permitted. Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
The magazine 8 is not operating correctly. Clean and lubricate the magazine slider 7 as required
and make sure that the magazine 8 is not dirty/soiled.
The spring of the magazine slider is too week or defective. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The sealing ring of the piston is worn or damaged. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
Frequent jamming of nails in the shot duct.
The fasteners being used are not permitted. Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
Contact an authorised service agent for Bosch power
tools.
The driven nails are bent.
The driver blade is damaged. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
Contrary to working with normal operating speed, the nails are
not driven in deep enough at higher operating speed.
The interior diameter of the supply-air hose is too low. Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 13)
The compressor is not suitable for fast operating speeds. Use a compressor that is sufficiently dimensioned for
the number of connected pneumatic tools and the oper-
ating speed.
Problem Cause Corrective Measure
OBJ_BUCH-1037-005.book Page 16 Monday, November 10, 2014 12:55 PM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSN 90-21 RK Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSN 90-21 RK Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info