Manual Bosch GSL 2 Professional (page 15 of 208) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591980

Zoom out

Zoom in

1/208

English | 15

Bosch Power Tools 1 609 92A 0L2 | (3.6.14)

Assembly

Power Supply of the Surface Laser

The measuring tool can either be operated with commercially

available batteries or with a Bosch lithium ion battery pack.

Operation with Batteries (see figure B)

Alkali-manganese batteries are recommended for the meas-

uring tool.

For installation and removal of the batteries, the measuring

tool’s height adjustment must be set to the lowest position.

For this, turn the thumbwheel for height adjustment 9 in anti-

clockwise direction to the stop.

To open the battery lid 7, press on the latch 6 and fold the bat-

tery lid up. Insert the batteries. When inserting, pay attention

to the correct polarity according to the representation on the

inside of the battery lid.

Always replace all batteries at the same time. Only use batter-

ies from one brand and with the identical capacity.

 Remove the batteries from the measuring tool when

not using it for extended periods. When storing for ex-

tended periods, the batteries can corrode and self-dis-

charge.

Operation with Battery Pack (see figure C)

 Use only original Bosch lithium ion battery packs with

the voltage listed on the nameplate of your measuring

tool. Using other battery packs can lead to injuries and

pose a fire hazard.

Note: Use of battery packs not suitable for the measuring tool

can lead to malfunctions of or cause damage to the measuring

tool.

Note: The battery pack is supplied partially charged. To en-

sure full capacity of the battery pack, completely charge the

battery pack in the battery charger before using for the first

time.

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium-ion battery pack that can be used in your measuring

tool.

The Lithium-Ion battery pack can be charged at any time with-

out reducing its service life. Interrupting the charging proce-

dure does not damage the battery pack.

The battery pack is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery pack service life is

achieved in this manner.

For installation and removal of the battery pack 23, the meas-

uring tool’s height adjustment must be set to the lowest posi-

tion. For this, turn the thumbwheel for height adjustment 9 in

anticlockwise direction to the stop.

To insert the battery pack 23, press on the latch 6 and fold the

battery lid 7 up. Slide the charged battery pack completely in-

to the battery compartment and close the battery lid.

Operation with 1,5 Ah battery pack: In order to shut the

battery lid 7, the foam damper on the inside of the battery lid

must be removed.

To remove the battery pack 23, press on the latch 6 and fold

the battery lid 7 up. Pull the battery pack out of the battery

compartment.

Battery Status Indicator

The three green LEDs of battery status indicator 5 indicate the

charge condition of the batteries or the battery pack 23.

Power Supply of the Remote Control (GSL 2 Set)

Using alkali-manganese batteries is recommended for opera-

tion of the remote control.

To open the battery lid 20, press on the latch 21 and remove

the battery lid. Insert the batteries. When inserting, pay atten-

tion to the correct polarity according to the representation on

the inside of the battery lid.

Always replace all batteries at the same time. Only use batter-

ies from one brand and with the identical capacity.

 Remove the batteries from the remote control when

not using it for longer periods. When storing for longer

periods, the batteries can corrode and discharge them-

selves.

Operation

Starting Operation of the Surface Laser

 Protect the measuring tool against moisture and direct

sun light.

 Do not subject the measuring tool to extreme tempera-

tures or variations in temperature. As an example, do

not leave it in vehicles for a long time. In case of large vari-

ations in temperature, allow the measuring tool to adjust to

the ambient temperature before putting it into operation.

In case of extreme temperatures or variations in tempera-

ture, the accuracy of the measuring tool can be impaired.

 Avoid hard knocks to the measuring tool or dropping it.

Damaging the measuring tool can cause accuracy to be

Remote Control RC 2

Article number

3 601 K69 C00

Working range

20 m

Operating temperature

–10 °C...+50 °C

Storage temperature

–20 °C...+70 °C

Batteries

3 x 1.5 V LR03 (AAA)

Weight according to

EPTA-Procedure 01/2003

50 g

2) The working range can be decreased by unfavourable environmental

conditions (e.g. direct sun irradiation).

For clear identification of your remote control, see the serial number 22

on the type plate.

LED Capacity

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥ 1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-1545-006.book Page 15 Tuesday, June 3, 2014 4:54 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSL 2 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSL 2 Professional Manual

Product: