592533
15
Zoom out
Zoom in
Previous page
1/181
Next page
English | 15
Bosch Power Tools 1 609 92A 180 | (17.3.15)
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745-2-3:
a
h
=5.0m/s
2
, K=1.5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 17.03.2015
Assembly
Before any work on the machine itself, pull the mains
plug.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Mounting the Auxiliary Handle and Dust Cover
(see figure A)
Only work with the auxiliary handle 5 mounted.
Loosen screw 2 of the dust cover 6 using the provided Al-
len key 14.
–Place dust guard 6 onto the spindle flange. Move dust cov-
er 6 accordingly to suit your working conditions and work-
ing position.
–Tighten screw 2 again.
–Mount auxiliary handle 5 to dust cover 6.
Mounting a Guide Roller (see figure B)
Mount guide roller 11 with the wing nuts 12 to the dust cover.
Mounting the Spindle Extension (see figure C)
Press spindle lock 1 and mount spindle extension 10 using
an open-end spanner (size 21 mm).
–Insert feather key 7 into spindle extension 10.
Mounting Application Tools (see figure D)
Press the spindle lock 1.
Slide the application tool onto the spindle extension. En-
sure that the feather key 7 is tightly seated.
Tighten locking screw 8.
Pay attention that the arrow directions on the application tool
and the housing of the power tool correspond.
Choice of Application Tool/Abrasive
Depending on the material to be worked and the required rate
of material removal, different application tools/abrasives are
available:
Rollers with permanent abrasive
Rollers for use with changeable sanding belts
Deflection rollers for use with sanding belts
Operation
Starting Operation
Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate
of the machine.
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Grain size
For dry sanding and pre-sanding coarse 40, 60
For structuring and for smoothing
out minor unevenness
medium
80
Combination-
fleece rollers
For satin-finishing and matt-
finishing of metal surfaces fine
120–240
Fleece rollers
OBJ_BUCH-1845-003.book Page 15 Tuesday, March 17, 2015 9:53 AM
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSI 14 CE Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSI 14 CE Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info