Manual Bosch GSB 24-2 (page 20 of 277) (All languages)

786458

Zoom out

Zoom in

1/277

20 | English

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Setting the Rotational Direction (seefiguresJ–K)

uOnly push the rotational direction switch(5) when the

power tool is not in use.

The rotational direction switch (5) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (7) is being pressed.

Clockwise rotation: To drill and drive in screws, slide the

rotational direction switch(5) downwards on the left-hand

side and upwards on the right-hand side at the same time.

Anti-clockwise rotation: To loosen and unscrew screws and

nuts, slide the rotational direction switch(5) upwards on the

left-hand side and downwards on the right-hand side at the

same time.

Setting the Operating Mode

Drilling and screwdriving

Set the selector switch (2) to the "drilling"

symbol.

Impact drilling

Set the selector switch (2) to the "impact

drilling" symbol.

The selector switch (2) clicks into place and

can also be actuated when the motor is running.

Mechanical Gear Selection

uYou can press the gear selector switch (9) with the

power tool running at a low speed. You should not do

this at full load or maximum torque, or when the tool is

not in use, however.

You can preselect two speed ranges with the gear selector

(9).

First gear:

Low speed range; for working with a large

drilling diameter or for screwdriving.

Second gear:

High speed range; for working with a small

drilling diameter.

If the gear selector (9) cannot be swivelled all the way to the

stop, turn the drive spindle slightly with the drill.

Switching on/off

To start the power tool, press and hold the on/off switch

(7).

Press the lock-on button (6) to lock the on/off switch (7) in

this position.

To switch off the power tool, release the on/off switch (7);

or, if the switch is locked with the lock-on button (6), briefly

press the on/off switch (7) and then release it.

Overload clutch

The power tool is equipped with an overload

clutch (anti-rotation) to limit high torque reac-

tions.

uIf the application tool jams or snags, the power trans-

mission to the drill spindle will be interrupted. Always

hold the power tool firmly with both hands to with-

stand the forces this may create and adopt a position

with stable footing.

uSwitch the power tool off immediately and remove the

application tool if the power tool becomes blocked.

Switching on when the drilling tool is blocked may

cause high torque reactions.

Rapid switch-off (Kickback Control)

(GSB 24-2) The rapid shut-off function (KickBack Con-

trol) gives the user greater control over the

power tool and offers them better protec-

tion than power tools that do not have Kick-

Back Control. The power tool will switch off if it suddenly

and unforeseeably rotates around the drilling axis.

To switch the tool back on, release the on/off switch and

then press it again twice.

uIt will no longer be possible to switch the power tool

on if the KickBack Control function is faulty. Have the

power tool serviced by a qualified repair person using

only original replacement parts.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (7) to varying ex-

tents.

Applying light pressure to the on/off switch (7) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Preselecting the speed/impact rate

You can preselect the required speed/impact rate using the

speed preselection thumbwheel (8), even during operation.

The required speed/impact rate is dependent on the mater-

ial and the work conditions and can be determined by prac-

tical trials.

Speed Electronic Preselection (GSB 21-2 RCT)

With the thumbwheel for electronic speed preselection(3),

the required speed/impact frequency can be selected even if

the machine is running.

1 609 92A 7YU | (01.06.2022) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSB 24-2 in the language / languages: All languages as an attachment in your email.

The manual is 5.49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSB 24-2 Manual

Product: