Manual Bosch GSB 20-2 RCE (page 23 of 136) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78438

Zoom out

Zoom in

1/136

English | 23

Bosch Power Tools 1 609 929 T17 | (20.10.09)

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Reversing the Rotational Direction

(see figures G–H) (GSB 20-2 RE/

GSB 20-2 RCE/GSB 20-2 RET)

f Actuate the rotational direction switch 5

only when the machine is at a standstill.

The rotational direction switch 5 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 6 actuated.

Right rotation: For drilling and driving in

screws, push the rotational direction switch 5

downward on the left side and at the same time

upward on the right side.

Left rotation: For loosening and unscrewing

screws and nuts, push the rotational direction

switch 5 upward on the left side and at the same

time downward on the right side.

Setting the Operating Mode

Drilling and Screwdriving

Set the selector switch 2 to the “Drill-

ing” symbol.

Impact Drilling

Set the selector switch 2 to the “Im-

pact drilling” symbol.

The selector switch 2 engages noticeably and

can also be actuated with the machine running.

Gear Selection, Mechanical

f The gear selector 9 can be actuated at

standstill or when the machine is running.

However, this should not be done while op-

erating at full load or maximum speed.

Two speed ranges can be preselected with the

gear selector 9.

Gear I:

Low speed range; for working with

large drilling diameter or for driv-

ing in screws.

Gear II:

High speed range; for working with

small drilling diameter.

If the gear selector 9 cannot be fully engaged,

lightly rotate the drive spindle with the drill bit

by twisting the drill chuck.

Switching On and Off

To start the machine, press the On/Off switch 6

and keep it pressed.

To lock the pressed On/Off switch 6, press the

lock-on button 8.

To switch off the machine, release the On/Off

switch 6 or when it is locked with the lock-on

button 8, briefly press the On/Off switch 6 and

then release it.

Safety Clutch

To limit dangerous reaction

torque, the machine is

equipped with a safety clutch

(anti-rotation).

f If the tool insert becomes caught or

jammed, the drive to the drill spindle is in-

terrupted. Because of the forces that occur,

always hold the power tool firmly with both

hands and provide for a secure stance.

f If the power tool jams, switch the machine

off and loosen the tool insert. When switch-

ing the machine on with the drilling tool

jammed, high reaction torques can occur.

OBJ_BUCH-115-003.book Page 23 Tuesday, October 20, 2009 8:47 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSB 20-2 RCE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GSB 20-2 RCE

Bosch GSB 20-2 RCE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 137 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSB 20-2 RCE Manual

Product: