786163

Bosch GSB 18V-150 C Manual

21
Zoom out
Zoom in
Previous page
1/297
Next page
English | 21
Swivelling the auxiliary handle
You can swivel the auxiliary handle (4) to any angle for a safe
work posture that minimises fatigue.
Turn the lower gripping end of the auxiliary handle (4) anti-
clockwise and swivel the auxiliary handle (4) into the re-
quired position. Afterwards, turn the lower gripping end of
the auxiliary handle (4) clockwise to retighten it.
Setting the drilling depth
You can use the depth stop(3) to set the required drilling
depth X.
Loosen the wing bolt for adjusting the depth stop (5) and in-
sert the depth stop into the auxiliary handle (4).
Pull the depth stop(3) far enough out that the distance
between the drill bit tip and the edge of the depth stop(3)
corresponds to the required drilling depth X.
Retighten the wing bolt for adjusting the depth stop (5).
Changing the tool (see figure A)
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (17) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation . This will automatically lock the
drill chuck.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (16) to the middle posi-
tion to avoid unintentionally switching it on. Insert the
charged battery (11) into the handle until you feel it engage
and it is flush with the handle.
Setting the rotational direction (see figure B)
The rotational direction switch (16) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (17) is being pressed.
Rotate clockwise: Slide the rotational direction
switch (16) on both sides until it stops in the posi-
tion.
Rotate anti-clockwise: Slide the rotational direction
switch (16) on both sides until it stops in the posi-
tion.
Setting the operating mode
Drilling
Set the mode selector switch(7) to the
"drilling" symbol.
Screwdriving
Set the mode selector switch(7) to the "screw-
driving" symbol.
Impact drilling (GSB 18V-150 C)
Set the mode selector switch(7) to the "impact
drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(17).
The LED (13) lights up when the on/off switch (17) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (17).
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (17) to varying extents.
A light pressure on the on/off switch (17) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Preselecting torque (applies to screwdriving mode)
The torque presetting ring (6) can be used to preselect the
required torque in 25 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical gear selection
uOnly operate the gear selector (8) when the power
tool is not in use.
Bosch Power Tools 1 609 92A 838 | (14.07.2022)
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSB 18V-150 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSB 18V-150 C in the language / languages: All languages as an attachment in your email.

The manual is 6.62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info