Manual Bosch GOP 250 CE (page 16 of 199) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544113

Zoom out

Zoom in

1/199

16 | English

2 609 932 802 | (14.2.12) Bosch Power Tools

Mounting/Replacing the Application Tool/Accessory

(GOP 250 CE)

If required, remove an already mounted application tool/ac-

cessory.

For removing the application tool/accessory, loosen the

screw 7 with the Allen key 8 and remove the application tool/

accessory.

Mount the requested application tool/accessory (e.g. plunge

cut saw blade 6) in such a manner on the tool holder 4 that the

offset faces downward (see illustration on the graphics page;

marking on the application tool/accessory is readable from

above).

Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 4. 12 different positions are possible, each

offset by 30°.

For more intermediate positions, the adapter 9 (accessory)

can be used: Allow the adapter to engage with the smooth

side onto the cams of the tool holder 4 (see illustration on the

graphics page). Position the application tool/accessory onto

the adapter in any position.

Fasten the application tool/accessory with bolt 7. Tighten the

bolt with Allen key 8 until the spring washer of the bolt faces

flush against the application tool/accessory.

f Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting/Replacing the Application Tool/Accessory

(GOP 300 SCE)

If required, remove an already mounted application tool/

accessory.

For this, open the SDS lever 12 to the stop (not further) and

remove the application tool.

Mount the requested application tool/accessory (e.g. plunge

cut saw blade 6) in such a manner on the tool holder 4 that the

offset faces downward (see illustration on the graphics page;

marking on the application tool/accessory is readable from

above).

Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 4. 12 different positions are possible, each

offset by 30°.

Close SDS lever 12 so that it faces against the housing of the

power tool.

f Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting/Replacing a Sanding Sheet on the Sanding Plate

The sanding plate 10 is fitted with Velcro backing for quick

and easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 11, free the Velcro back-

ing of the sanding plate 10 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 11 flush alongside one edge of the

sanding plate 10, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

To remove the sanding sheet 11, grasp it at one of the tips and

pull it off from the sanding plate 10.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:

Scraper, flexible* Silicone and other

elastic materials

Base plate for

sanding, series

Delta 93 mm*

Depends on sanding

sheet

Accessory Material

* Optional accessory; for the complete accessories please see Bosch

accessory programme.

Sanding disc Material Application Grain size

– All wooden materials

(e.g., hardwood, soft-

wood, chipboard, build-

ing board)

– Metal materials

For coarse-sanding, e.g. of rough, unplaned beams and

boards

coarse 40

For face sanding and planing small irregularities

medium 80

100

120

For finish and fine sanding of wood

fine 180

240

320

400

OBJ_BUCH-1271-004.book Page 16 Tuesday, February 14, 2012 11:38 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GOP 250 CE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GOP 250 CE Manual

Product: