78975
27
Zoom out
Zoom in
Previous page
1/163
Next page
English | 27
Bosch Power Tools 1 609 929 K57 | (27.11.07)
Determining the Slot Width
The slot width results from the amount of spac-
er discs 19 between the two diamond cutting
discs 18 and the cutting width of the diamond
cutting discs.
The slot width is calculated as follows:
Slot width = Thickness of the spacer discs +
width of the diamond cutting discs.
The allowable slot width is shown in the section
“Technical Data”.
The machine can be operated with one or two
diamond cutting discs.
Mounting the Clamping Assembly
(see figure A)
Set the mounting flange 17 onto the grinder
spindle 16. The mounting flange with its driving
feature must be properly seated on the grinding
spindle.
Place the diamond cutting disc 18 and the spac-
er discs 19 on the mounting flange 17.
f Regardless of the requested slot width, all
spacer discs 19 provided must always be
mounted. Otherwise, the diamond cutting
disc 18 can become loose during operation
and lead to injuries.
Amount of required spacer discs:
GNF 20 CA: 5 pce., each 4 mm thick
GNF 35CA: 3pce., each 4mm thick and 4pce.,
each 6 mm thick.
At least one spacer disc 19 must be mounted be-
tween two diamond cutting discs 18.
When mounting the diamond cutting discs, en-
sure that the direction-of-rotation arrows on the
diamond cutting discs match with the rotation
rotation direction of the machine (see direction-
of-rotation arrow on the gear case).
Press the spindle lock button 9 to lock the grind-
ing spindle.
Screw on the clamping nut 20 and tighten it with
the two-pin spanner 1.
Swivel the cutting unit back again. Check the
locking system of the cutting unit by pulling the
handle.
When working with 2 diamond cutting discs 18,
always replace them in pairs.
See graphics page for the mounting sequence.
Operation
Pre-selecting the Cutting Depth
f The cutting depth may only be pre-selected
when the machine is switched off.
The requested cutting depth can be pre-select-
ed with the depth stop 6.
Press the button for depth stop adjustment 5
and push the depth stop 6 to the requested cut-
ting depth on the cutting-depth scale 4. Release
button 5 again.
Ensure that the depth stop 6 is engaged again.
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
f Before starting the machine, check if the
cutting unit has engaged in the upper posi-
tion. Otherwise the diamond cutting discs
can touch the workpiece, resulting in possi-
ble loss of control over the power tool when
switching on.
To start the power tool, push the On/Off switch
10 forwards.
To lock the On/Off switch 10, press the On/Off
switch 10 down at the front until it latches.
To switch off the power tool, release the On/Off
switch 10 or, if it is locked, briefly push down
the back of the On/Off switch 10 and then re-
lease it.
f Check the diamond cutting discs before
use. The diamond cutting disc(s) must be
mounted properly and be able to rotate
freely. Carry out a test run for at least
30 seconds without any load. Do not use
diamond cutting discs that are damaged,
out-of-balance, or vibrate. Damaged dia-
mond cutting discs can rupture and lead to
injuries.
OBJ_BUCH-126-001.book Page 27 Tuesday, November 27, 2007 9:54 AM
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GNF 20 CA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GNF 20 CA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info