Manual Bosch GLM 250 VF Professional (page 21 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

592062

Zoom out

Zoom in

1/319

English | 21

Bosch Power Tools 1 609 92A 0KT | (23.4.14)

Upon completion of the third mea-

surement, the volume is automatical-

ly calculated and displayed in the re-

sult line c. The individual measured

values are displayed in the measured-

value lines a.

Values above 999999 m

cannot be indicated; “ERROR” and

“––––” appear on the display. Divide the volume to be

measured into individual measurements; their values can

then be calculated separately and then summarized.

Indirect Length Measurement (see figures H–K)

The indirect length measurement is used to measure distanc-

es that cannot be measured directly because an obstacle

would obstruct the laser beam or no target surface is available

as a reflector. Correct results are achieved only when the right

angles required for the respective measurement are exactly

adhered to (Pythagorean Theorem).

Pay attention that the reference point of the measurement

(e.g. the rear edge of the measuring tool) remains exactly at

the same location for all individual measurements within a

measuring sequence (exception: trapezium measurements).

The laser beam remains switched on between the individual

measurements.

For indirect length measurements, four measuring modes are

available. Each measuring mode can be used for determining

different distances. To select the measuring mode, press the

function-mode button 3 until the symbol of the desired mea-

suring mode is indicated on the display.

a) Simple Pythagoras Measurement (see figure H)

Press the function-mode button 3 until the indication for sim-

ple Pythagoras measurement appears on the display.

Measure distances “1” and “2” in this sequence with a length

measurement. Pay attention that a right angle exists between

distance “1” and the sought distance “E”.

Upon completion of the last measure-

ment, the result for the sought dis-

tance “E” is displayed in the result

line c. The individual measured values

are displayed in the measured-value

lines a.

b) Double Pythagoras Measurement (see figure I)

Press the function-mode button 3 until the indication for dou-

ble Pythagoras measurement appears on the display.

Measure distances “1”, “2” and “3” in this sequence with a

length measurement. Pay attention that a right angle exists

between distance “1” and the sought distance “E”.

Upon completion of the last measure-

ment, the result for the sought dis-

tance “E” is displayed in the result

line c. The individual measured values

are displayed in the measured-value

lines a.

c) Combined Pythagoras Measurement (see figure J)

Press the function-mode button 3 until the indication for com-

bined Pythagoras measurement appears on the display.

Measure distances “1”, “2” and

“3” in this sequence with a

length measurement. Pay attention that a right angle exists

between distance “1” and the sought distance “E”.

Upon completion of the last measure-

ment, the result for the sought dis-

tance “E” is displayed in the result

line c. The individual measured values

are displayed in the measured-value

lines a.

d) Trapezium Measurement (see figure K)

Press the function-mode button 3 until the indication for tra-

pezium measurement appears on the display.

Measure distances “1”, “2” and “3” in this sequence with a

length measurement. Pay attention that the measurement of

distance “3” starts exactly at the end point of distance “1”

and that a right angle exists between distances “1” and “2” as

well as between “1” and “3”.

Upon completion of the last measure-

ment, the result for the sought dis-

tance “E” is displayed in the result

line c. The individual measured values

are displayed in the measured-value

lines a.

Time-delayed Length Measurement

Time-delayed length measurement is helpful e.g. when mea-

suring at hard to reach locations or when movements of the

measuring tool during measuring are to be prevented.

For a time-delayed length measurement, press function-

mode button 3 until the indicator for time-delayed length

measurement appears on the display.

The time period from the actuation until the measurement

takes place is displayed in the measured-value line a. The time

period can be adjusted between 1 s and 60 s by pressing the

plus button 6 or the minus button 12.

Then press the measuring button 7 to

switch the laser beam on and aim at

the target point. Press the measuring

button 7 again to actuate the mea-

surement. The measurement takes

place after the set time period. The

measured value is displayed in the re-

sult line c.

The addition and subtraction of measuring results as well as

minimum/maximum measurements are not possible for time-

delayed length measurements.

Wall Surface Measurement (see figure L)

The wall surface measurement is used to determine the sum

of several individual surfaces with a common height.

OBJ_BUCH-947-005.book Page 21 Wednesday, April 23, 2014 9:23 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 250 VF Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 250 VF Professional Manual

Product: