544285
190
Zoom out
Zoom in
Previous page
1/239
Next page
190 | 中文
1 609 92A 0KJ | (6.5.14) Bosch Power Tools
安装
安装 / 更换电池
只能使用碱性锰电池。
打开电池盒盖 8 时,必须先朝着箭头的方向推移电池
盒盖的固定扳扣 11,接著再拿下盒盖。安装好电池。
根据电池盒内的图案安装电池,请注意正确的极性位
置。
如果电池的显示灯 5 闪烁红灯,便需要更换电池。
务必同时更换所有的电池。请使用同一制造厂商,相
同容量的电池。
不使用测量仪时,必须从仪器中取出电池。 长期搁
置之后,电池会腐蚀或自行放电。
正式操作
正式操作仪器
不可以让湿气渗入仪器中,也不可以让阳光直接照
射在仪器上。
仪器不可以曝露在极端的气候下,也不可以把仪器
放在温差相当大的环境中。 仪器不可以长期放置在
汽车中。如果仪器先后曝露在温差相当大的环境
中,必须先等待仪器温度恢复正常后再使用仪器。
如果仪器曝露在极端的气候下或温差相当大的环境
中,会影响仪器的测量准确度。
避免强烈撞击测量仪器,勿让仪器掉落地面。 如果
测量仪曾经遭受强烈的外来冲撞,必须在使用仪器
之前先检查仪器的测量精度(参考 " 找平精度 ")
搬运仪器之前必须先关闭仪器。 关机后摆动零件会
被锁定,否则摆动零件可能因为强烈的震动而受
损。
开动 / 关闭
开动测量仪器,把起停开关 7 推移到 "on"位置
(不使用自动找平功能操作仪器时),或 "on"
(使用自动找平功能操作仪器时)。开机后测量仪
器马上从激光放射口 1 投射出激光线段。
不可以把激光指向人或动物。您本人也不可以直视
激光。就算您与激光之间尚有一段距离,也不可忽
视激光的伤害力。
关闭测量仪器,把起停开关 7 推移到 "off" 位置。关
闭仪器后,仪器的摆动单元会被锁定。
关闭仪器的自动关机功能
在操作 30 分钟后,测量仪器会自动关闭。为了关闭
仪器的自动关机功能,在开动仪器时得按住操作功能
转换键 4,并在 3 秒钟后放开按键。如果自动关机功
能被关闭了,激光线段会在 3 秒钟后快闪一下。
看管好已经开动的仪器。使用完毕后务必随手关闭
仪器。 激光可能扰乱旁人的视线。
启动仪器的自动关机功能时,先关闭仪器并再度开动
仪器 (不必按住操作功能转换键 4)。
操作功能 ( 参考插图 AD)
本测量仪具备了三种测量功能,您可以随时转换测量
功能:
水平找平 "–": 会产生水平激光束,
垂直找平 "l": 会产生垂直激光束,
交叉找平 "+": 会产生一道水平和一道垂直的激光
束。
开动仪器后,测量仪是设定为交叉找平。按下操作功
能转换键 4 后能够改变仪器的测量功能。
以上三种测量方式,都可以使用自动找平功能。
脉冲功能
使用激光接收器 21 时,不管选择何种测量方式,都
必须开启脉冲功能。
启动脉冲功能后,激光线段会以极高的频率闪烁,这
样激光接收器 21 才能够接收仪器投射出的激光。
按下按键 3 可以开动脉冲功能。启动脉冲功能之后显
示灯 2 会亮起绿光。
就肉眼而言,在启动脉冲功能之后,激光线段的辨识
程度会降低。因此不使用激光接收器时,最好重新按
下按键 3 来关闭脉冲功能。关闭脉冲功能之后显示灯
2 会熄灭。
自动找平功能
使用自动找平功能进行测量 (参考插图 C)
把测量仪器放置在水平、坚固的底垫上。或者把仪器
固定在一般的三脚架上。
使用自动找平功能测量时必须把起停开关 7 推到
"on"的位置。
自动找平功能能够校平小的起伏,它的校平范围在
±4 度之间。只要激光束不再闪烁,则表示测量仪已
经完成找平的工作。
如果仪器无法自动找平,例如仪器的放置位置的水平
倾斜度超过 4 度,激光束会持续闪烁,此时必须把仪
器移动到平坦的水平的位置上,并且静待仪器自动找
平。
如果在测量中途碰了仪器或移动了仪器,仪器会重新
自动找平。此时,最好拿一个基准点重新检查水平激
光束和垂直激光束的位置,以避免测量错误。
不使用自动找平功能时的测量工作 (参考插图 D)
不使用自动找平功能测量时必须把起停开关 7 推移到
"on"的位置。测量时如果不使用自动找平功能,
激光束会保持在闪烁的状态。
关闭了自动找平功能后,便可以把测量仪拿在手上,
或者放在合适的底垫上操作。进行交叉测量时,水平
激光束和垂直激光束的交叉角便不会被强制成 90 度。
OBJ_BUCH-817-005.book Page 190 Tuesday, May 6, 2014 10:15 AM
190


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GLL 2-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLL 2-50 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info