786130

Bosch GLI 18V-10000 C Manual

12
Zoom out
Zoom in
Previous page
1/163
Next page
12 | English
Cordless worklight GLI 18V-10000 C
Level 1 lm 1000
Level 2 lm 5 000
Level 3 lm 10 000
Recommended ambient tem-
perature during charging °C 0 to +35
Permitted ambient temperat-
ure during operationB) and
during storage
°C –20 to +50
Recommended rechargeable
batteries GBA 18V...
ProCORE18V...
Recommended chargers GAL 18...
GAX 18...
GAL 36...
Button cell V
type 3
CR 2032
Protection class /III
Data transfer
Bluetooth®C) Bluetooth® 4.2
(Low Energy)
Signal rangeD) m 15
Frequency range used MHz 2402–2480
Output power mW <2
A) At maximum brightness incl. remaining operating time in
dimmed mode
B) Limited performance at temperatures <0°C
C) The mobile devices must be compatible with the Bluetooth® ver-
sion specified and support the Generic Access Profile (GAP).
D) The signal range may vary greatly depending on external condi-
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).
The colour rendition of illuminated objects can be distorted.
System requirements
Mobile device (tablet, smart-
phone) Android,iOS A)
A) Minimum system requirements can be found in the app store for
your mobile device (e.g. Google Play or iTunes).
Assembly
Putting the button cell into operation
(seefigureA)
The cordless worklight is fitted with a button cell so that it
can be detected by the mobile device even if no battery(8)
is inserted.
Remove the separating film between the button cell(12)
and the button cell contact when using the tool for the first
time.
To open the battery compartment cover(11), turn it anti-
clockwise with a screwdriver and then lift off the battery
compartment cover. Remove the film from the button cell
contact and close the battery compartment cover back up.
Battery Charging (Accessory)
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
cordless worklight.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". A protective circuit
switches the cordless worklight off when the battery is
drained.
uDo not continue to press the On/Off switch after the
worklight has been automatically switched off. The
battery can be damaged. Ensure that the battery is
charged and that the worklight has cooled before switch-
ing on the worklight again.
To remove the battery(8), press the release button(10)
and pull the battery out of the cordless worklight. Do not use
force to do this.
Follow the instructions on correct disposal.
Operation
Starting Operation
Inserting the battery (seefigureA)
Push the charged battery pack(8) into the battery
holder(14) until it clicks into place.
Setting up
Place the cordless worklight on a stable, level surface. Make
sure it is secure.
The safety brackets(3) protect the light(1) from damage,
should the cordless worklight be accidentally knocked over.
Fastening to the Tripod
You can use the tripod mount(9) to screw the cordless
worklight onto a tripod.
Attach the cordless worklight firmly to the tripod. Ensure the
cordless worklight cannot come loose and/or fall over.
Ensure that the tripod has a firm footing.
Switching on/off and adjusting the brightness
On/off switch Function
Press once Switches on the cordless worklight,
dimmed (level 1)
Press twice Switches on the cordless worklight,
dimmed (level 2)
Press three times Switches on the cordless worklight,
full brightness (level 3)
Press four times Switches off the cordless worklight
1 609 92A 7NH | (17.05.2022) Bosch Power Tools
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GLI 18V-10000 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLI 18V-10000 C in the language / languages: All languages as an attachment in your email.

The manual is 5.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info