382835

Bosch gks 66 ce Manual

16
Zoom out
Zoom in
Previous page
1/96
Next page
English - 4
Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
For starting operation of the machine, actuate
the lock-off button 2 first, and then press and hold
the On/Off switch 3 afterwards.
To switch off the machine, release the On/Off
switch 3.
For safety reasons the On/Off switch of
the machine cannot be locked; it must
remain pressed during the entire opera-
tion.
Speed Preselection (GKS 66 CE)
With the adjustment knob 5, the speed can be
continuously selected. The required speed is de-
pendent on the saw blade used and the material
to be worked (see Saw Blade Table).
Constant Electronic Control
(GKS 66 CE)
The constant electronics ensures that the ma-
chine speed is the same regardless of the load
conditions; this ensures uniform work advancing
and a smooth cutting pattern.
Temperature Dependent Overload
Protection (GKS 66 CE)
When the machine is overloaded while sawing,
the motor stops and starts again only when the
advancing rate is reduced. For machines that
have become warm during operation, the temper-
ature dependent overload protection will react
earlier. The reaction time will be dependent on
the initial temperature of the machine.
Reduced Starting Current (GKS 66 CE)
Due to the gradual, smooth starting procedure of
the machine, a 13 A fuse is sufficient.
■ Before any work on the machine itself, pull
the mains plug.
■ Wear protective gloves.
■ The saw blades used must correspond to
the characteristic data in these operating
instructions.
■ Use only saw blades with an allowable
speed matching at least the no-load speed
of the machine.
Removing (see figure )
Press spindle lock 1 and keep depressed.
■ The spindle lock 1 may be actuated only
when the saw blade is at a standstill.
Unscrew clamping bolt 18 with the Allen key 17.
Remove clamping flange 19.
Tilt back the retracting blade guard 13 and hold
firmly.
Remove the saw blade.
Mounting (see figure )
Clean the saw blade and all the clamping parts to
be assembled.
Tilt back the retracting blade guard 13 and hold
firmly.
Place the saw blade onto the mounting flange 20.
Assemble the clamping bolt 18 with the washer
and assemble the clamping flange 19.
Tighten the clamping bolt 18 with the Allen
key 17. Tightening torque: 6 –9 Nm; equivalent to
hand-tight plus
1
/
4
turn.
Take care that the mounting positions of
the mounting flange 20 and clamping
flange 19 are correct.
When mounting: Ensure that the cutting di-
rection of the teeth (direction of arrow on
saw blade) and the direction-of-rotation ar-
row on the blade guard match.
Initial Operation
Changing the Tool
A
A
1 609 929 535 - Buch Seite 4 Dienstag, 16. September 2003 11:34 11
16 • 1 609 929 535 • TMS • 10.09.03
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch gks 66 ce at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gks 66 ce in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info