Manual Bosch gks 66 ce (page 15 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

382835

Zoom out

Zoom in

1/96

English - 3

■ The saw blade and riving knife must not be-

come stuck in the cut. The saw teeth setting

must be wider and the main body of the saw

blade thinner than the thickness of the riving

knife.

■ Protect saw blades against shock and impact.

■ Do not wedge the saw blade.

■ If the saw blade jams, switch off the machine

immediately.

■ The spindle lock 1 may be actuated only when

the saw blade is at a standstill.

■ After switching off, do not slow down the saw

blade by exerting side pressure.

■ Always switch the machine off and wait until it

has come to a standstill before placing it down.

■ Use only sharp, flawless saw blades. Change

cracked, bent or dull saw blades immediately.

■ Saw blades of high alloy, high-speed steel

must not be used.

■ Never allow children to use the machine.

■ Bosch is only able to ensure perfect operation

of the machine if the original accessories in-

tended for it are used.

■ Before any work on the machine itself, pull

the mains plug.

Checking the Adjustment

of the Riving Knife

For safety reasons the riving knife 21 must al-

ways be used. The riving knife avoids seizing of

the saw blade while sawing.

The adjustment takes place at the maximum cut-

ting depth.

Loosen the screw 15, adjust the riving knife 21

and retighten the screw.

■ Before any work on the machine itself, pull

the mains plug.

☞

To achieve an optimum cut, the saw blade

must not protrude more than 3 mm at the

most from the material.

To adjust the cutting depth, loosen winged

screw 7 and raise the saw from the base plate 14

or lower it towards the base plate, respectively:

Raise ➡ for smaller cutting depths

Lower ➡ for greater cutting depths

Set the desired depth on the cutting depth

scale 6.

Retighten the winged screw 7.

■ Before any work on the machine itself, pull

the mains plug.

Loosen the winged screw 9.

Swing the machine to the side until the desired

cutting angle is set on the scale 8.

Tighten the winged screws again.

Note: For mitre cutting, the cutting depth is

smaller than the value shown on the cutting depth

scale 6.

The cutting mark 0° ( 23) indicates the position of

the saw blade for right-angled cuts.

The cutting mark 45° ( 24) indicates the position

of the saw blade for 45° cuts.

Note: It is best to carry out a trial cut.

Before Putting into Operation

2,5 - 5 mm

Adjusting the Cutting Depth

Adjusting the Cutting Angle

Cutting Marks

45°

0°

1 609 929 535 - Buch Seite 3 Dienstag, 16. September 2003 11:34 11

15 • 1 609 929 535 • TMS • 10.09.03

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gks 66 ce in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gks 66 ce Manual

Product: