708169
20
Zoom out
Zoom in
Previous page
1/291
Next page
20 | English
1 609 92A 4LL | (18.10.2018) Bosch Power Tools
power tool. If accessories run faster than their rated
speed, they may break and fly off.
u Do not use abrasive wheels as the application tool un-
der any circumstances.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions.
Removing the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
Press and hold the spindle lock button (5).
u Do not press the spindle lock button (5) while the saw
spindle is moving. The power tool may become damaged
if this happens.
Use the hex key (3) to undo the clamping bolt (25) in ro-
tational direction .
Swing the retracting blade guard (13) back and hold on
to it firmly.
Remove the clamping flange (24) and the saw blade (23)
from the saw spindle (21).
Fitting the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
Clean the saw blade (23) and all the clamping elements
to be fitted.
Swing the retracting blade guard (13) back and hold on
to it firmly.
Place the saw blade (23) on the mounting flange (22).
The cutting direction of the teeth (direction of the arrow
on the saw blade) must match the rotational direction of
the arrow on the retracting blade guard (13).
Attach the clamping flange (24) and screw in the clamp-
ing bolt (25) in rotational direction . Ensure that the
mounting flange (22) and clamping flange (24) are in-
stalled in the correct position.
Press and hold the spindle lock button (5).
Use the hex key (3) to tighten the clamping bolt (25) in
rotational direction . The tightening torque should be
6–9Nm, which corresponds to hand-tight plus ¼ turn.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
Use a dust extraction system that is suitable for the ma-
terial wherever possible.
Provide good ventilation at the workplace.
It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
Fitting the dust extraction adapter (see figure B)
Push the dust extraction adapter (28) onto the chip ejector
(16) until it clicks into place. Then secure the dust extraction
adapter (28) in place with the screw (27).
A dust extraction hose with a diameter of 35mm can be con-
nected to the dust extraction adapter (28).
u The dust extraction adapter must only be fitted if an
external dust extraction system is connected. Other-
wise the extraction duct can become clogged.
u No dust bags should be connected to the dust extrac-
tion adapter. Otherwise the extraction system can be-
come clogged.
To ensure optimum extraction, the dust extraction adapter
(28) must be cleaned regularly.
External dust extraction
Connect the extraction hose (35) to a dust extractor (ac-
cessory). You will find an overview of connecting to various
dust extractors at the end of these operating instructions.
The power tool can be directly connected to the socket of a
Bosch all-purpose dust extractor with remote starter. This
dust extractor is started up automatically when the power
tool is switched on.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation
Operating modes
u Remove the battery before carrying out any work on
the power tool.
Setting the cutting depth (see figure C)
u Adapt the cutting depth to the thickness of the work-
piece. A space of less than the height of one full tooth
should be visible under the workpiece.
Loosen the clamping lever (29). For a smaller cutting depth,
pull the saw away from the base plate (6); for a larger cutting
depth, push the saw towards the base plate (6). Adjust the
desired cutting depth at the cutting-depth scale. Retighten
the clamping lever (29).
The clamping force of the clamping lever (29) can be read-
justed. To do so, unscrew the clamping lever (29) and
retighten it in a position offset by at least 30° in an anticlock-
wise direction.
Setting the mitre/bevel angle (GKS18V-57G)
We recommend that you place the power tool down on the
front side of the protective guard (17).
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GKS 18V-57 G Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GKS 18V-57 G Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info