591816
17
Zoom out
Zoom in
Previous page
1/235
Next page
English | 17
Bosch Power Tools 1 609 92A 0PX | (18.11.14)
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 8 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 9, press the battery unlocking button 8
and pull the battery upward out of the power tool. Do not ex-
ert any force.
Battery Charge-control Indication (see figure F)
The three green LEDs of the battery charge-control indicator
25 indicate the charge condition of the battery 9. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 24 to indicate the charge condition. This is also
possible when the battery 9 is removed.
When no LED lights up after pushing button 24, then the bat-
tery is defective and must be replaced.
Mounting/Replacing the Saw Blade
Before any work on the power tool, remove the battery.
When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Only use saw blades that correspond with the charac-
teristic data given in the operating instructions.
Use only saw blades with a diameter of min. 130 mm
and max. 136 mm.
Do not under any circumstances use grinding discs as
the cutting tool.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of this manual.
Removal of the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
Press the spindle lock button 1 and keep it pressed.
The spindle lock button 1 may be actuated only when
the saw spindle is at a standstill. Otherwise, the power
tool can be damaged.
–With the Hex key 5, unscrew the clamping bolt 16 turning
in rotation direction .
Tilt back the retracting blade guard 21 and hold firmly.
Remove the clamping flange 17 and the saw blade 18 from
the saw spindle 20.
Mounting the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
Clean the saw blade 18 and all clamping parts to be assem-
bled.
Tilt back the retracting blade guard 21 and hold firmly.
–Place the saw blade 18 onto the mounting flange 19. The
cutting direction of the teeth (direction of arrow on the saw
blade) and the direction-of-rotation arrow on the retract-
ing blade guard 21 must correspond.
–Mount the clamping flange 17 and screw in the clamping
bolt 16 turning in rotation direction . Observe correct
mounting position of mounting flange 19 and clamping
flange 17.
Press the spindle lock button 1 and keep it pressed.
–Use the hex key 5 to tighten the clamping bolt 16 in rota-
tion direction . The tightening torque should be
69 Nm, which corresponds to hand-tight plus 1/8 turn.
Dust/Chip Extraction
Before any work on the power tool, remove the battery.
Dusts from materials such as lead-containing coatings,
minerals and metal can be harmful to one’s health. Touch-
ing or breathing-in the dusts can cause allergic reactions
and/or lead to respiratory infections of the user or by-
standers.
Certain dusts, such as oak or beech dust, are considered
carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
LED Capacity
Continuous lighting 3 x green 2/3
Continuous lighting 2 x green 1/3
Continuous lighting 1 x green <1/3
Flashing light 1 x green Reserve
OBJ_BUCH-2231-001.book Page 17 Tuesday, November 18, 2014 3:22 PM
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GKM 18 V-LI Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GKM 18 V-LI Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info