786141

Bosch GDS 18V-210 C Manual

18
Zoom out
Zoom in
Previous page
1/279
Next page
18 | English
Cordless Impact Wrench GDR 18V-210 C GDX 18V-210 C GDS 18V-210 C
Data transfer
Bluetooth®C) Bluetooth® 4.1
(Low Energy)
Bluetooth® 4.1
(Low Energy)
Bluetooth® 4.1
(Low Energy)
Signal interval s 8 8 8
Max. signal rangeD) m 30 30 30
A) Measured at 20–25°C with rechargeable battery ProCORE18V 8.0Ah
B) Measured withGBA 18V 1.5Ah and GBA 18V 12 Ah.
C) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.1) and support the Generic Access Profile
(GAP).
D) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
Noise/vibration information
GDR 18V-210 C / GDX 18V-210 C:
Noise emission values determined according to
EN62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 96dB(A); sound power level
107dB(A). Uncertainty K=3dB.
Wear hearing protection!
GDS 18V-210 C:
Noise emission values determined according to
EN62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 97dB(A); sound power level
108dB(A). Uncertainty K=3dB.
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty
K determined according to EN62841-2-2:
Impact tightening of fasteners of the maximum capacity of
the tool:
GDR 18V-210 C: ah=10 m/s2, K=1.5 m/s2
GDX 18V-210 C: ah=9 m/s2, K=1.5 m/s2
GDS 18V-210 C: ah=12.5 m/s2, K=1.5 m/s2
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (4) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (5) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (4), press the release button (5) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
1 609 92A 7X4 | (15.08.2022) Bosch Power Tools
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GDS 18V-210 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GDS 18V-210 C in the language / languages: All languages as an attachment in your email.

The manual is 9.51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info