786139

Bosch GDS 18V-1050 H Manual

22
Zoom out
Zoom in
Previous page
1/307
Next page
22 | English
rating plate of the power tool. Power tools marked
with 230V can also be operated with 220V.
uProducts that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
uAlways place the power tool down on its side and do
not lay it on the battery. The power tool can tip over de-
pending on the application tool and battery used.
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Push the charged battery(5) into the base of the power tool
until the battery is securely locked.
Set the rotational direction (see figureE)
The rotational direction switch (2) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (8) is being pressed.
Right rotation: To drive in screws and tighten nuts, press
the rotational direction switch (2) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (2) through to the right
stop.
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (8) to varying ex-
tents.
Applying light pressure to the on/off switch (8) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Switching on/off
To start the power tool, press and hold the on/off switch
(8).
The worklight (15) lights up when the on/off switch (8) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
To switch off the power tool, release the on/off switch (8).
User interface (see figures D–E)
GDS 18V-1000C / GDS 18V-1050HC:
The user interface(7) is used to preselect the speed and
working mode and to indicate the status of the power tool.
Status indications
Status indicator for power
tool(11) Meaning/cause Solution
Green Status OK –
Yellow Critical temperature has been reached or re-
chargeable battery is almost empty Run the power tool at no load and allow it to
cool down, or replace or charge the battery
soon
Illuminated red Power tool has overheated or rechargeable
battery is empty Allow the power tool to cool down, or replace
or charge the battery
Flashing blue Power tool is connected to a mobile device or
settings are being transferred –
Speed preselection
With the speed preselection button (16), you can preselect
the required speed in three stages. Press button (16) as of-
ten as needed until the required setting is indicated in the
speed indicator (17). The selected setting will be saved.
GDS 18V-1000C / GDS 18V-1050HC:
You can also preselect the speed using the Bosch Toolbox
app.
The required speed depends on the material and the work-
ing conditions; it can be ascertained through practical tests.
The information in the table below describes the recommen-
ded values.
Basic speed setting at level
123
[min-1] [min-1] [min-1]
Number of speed settings
30–1 100 0–2 300 0–3 400
You can use the button for speed preselection (16) to
preselect the required speed, even during operation.
Switching On the Worklight
GDS 18V-1000 / GDS 18V-1050H:
To switch the worklight(15) on or off, press the worklight
button(13).
uDo not look directly into the worklight; it can blind
you.
Selecting the working mode
GDS 18V-1000C / GDS 18V-1050HC:
The power tool has two preset working modes A and B (12).
You can also programme working modes for different applic-
ations and adjust existing modes via the Bosch Toolbox un-
der A and B (12).
To switch between the working modes A and B (12), press
button (14).
1 609 92A 7X5 | (04.07.2022) Bosch Power Tools
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GDS 18V-1050 H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GDS 18V-1050 H in the language / languages: All languages as an attachment in your email.

The manual is 11.42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info