786182
16
Zoom out
Zoom in
Previous page
1/85
Next page
16 | English
Dust cap(4) for SDS plus fixed chuck for drilling diamet-
ers of 16−26mm
In addition, you must change the dust cap if its wall contact
surface shows clear signs of wear and is causing dust to es-
cape through the extraction brush during extraction.
Removing the dust cap(1)/(3):
Press the locking button(23) and pull the dust cap up-
wards out of the holder.
Fitting the dust cap(1)/(3):
Push the new dust cap down into the holder until the lock-
ing button audibly engages.
The extension(20) is required if you use drill bits with a total
length of 165−265mm.
Mount and remove the extension(20) according to the
assembly/removal of the dust cap.
Emptying the Dust Box (seefigureG1–G4)
Note: Wear a dust mask when performing maintenance and
cleaning on the dust box.
Empty the dust box(24) after completing your work and as
needed, in order to ensure that the dust extraction attach-
ment continues to perform optimally. The viewing
window(15) enables you to check how full the dust box is.
Hold the power tool with the dust extraction attachment
horizontally and switch on the dust extraction attachment
for a few seconds.
This will cause residual dust to be sucked out of the ex-
traction channel into the dust box(24).
Press both the left-hand and right-hand release
buttons(16) and pull the dust box(24) out of the dust
extraction attachment.
Shake out the dust box(24) over a suitable waste bin.
Press both the left-hand and right-hand locking tabs(26)
inwards and pull the HEPA filter(25) out of the dust box.
Carefully tap against the HEPA filter to empty it or brush
down the flaps of the HEPA filter using a soft brush.
Note: Do not clean the HEPA filter with water and do not
use compressed air to blow it clean.
Put the HEPA filter(25) back in the dust box(24) after
cleaning it. Then slide the dust box into the dust extrac-
tion attachment until the release buttons(16) audibly en-
gage.
Maintenance and Service
Maintenance and Cleaning
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
uTo ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
Clean the dust extraction attachment using a dry, soft
cloth.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
Disposal
Dust extraction attachments, batteries, ac-
cessories and packaging should be sorted for
environmentally friendly recycling.
Do not dispose of dust extraction attachments
and batteries/rechargeable batteries into
household waste!
Only for EU countries:
According to the Directive 2012/19/EU on waste electrical
and electronic equipment and its transposition into national
law, dust extraction attachments that are no longer usable,
and, according to the Directive 2006/66/EC, defective or
1 609 92A 7YA | (11.07.2022) Bosch Power Tools
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GDE 18V-26 D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GDE 18V-26 D in the language / languages: All languages as an attachment in your email.

The manual is 4.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info