Manual Bosch GDE 18V-16 (page 8 of 76) (All languages)

786256

Zoom out

Zoom in

1/76

8 | English

1 609 92A 19U | (30.9.16) Bosch Power Tools

Assembly

Mounting the Dust Extraction Attachment

(see figure A)

– Put the guide groove 11 of the rotary hammer on the hous-

ing guide 9 of the dust extraction attachment and slide the

dust extraction attachment onto the rotary hammer.

The dust extraction attachment must audibly engage.

– To disconnect the attachment, press the unlocking button

8, hold down the unlocking button and pull the dust extrac-

tion attachment off the rotary hammer.

Operation

Working Advice

Never use the dust extraction attachment without a fil-

ter. If the dust extraction attachment is used without a fil-

ter, larger particles of drilling dust can be flung towards the

user and the power tool can be damaged.

Only use an undamaged filter (no cracks, small holes,

etc.). Replace a damaged filter immediately.

Never carry the power tool by the dust extraction at-

tachment.

Note: The guide 4 is spring-loaded. The guide can spring for-

ward when the button 5 for drill bit length adjustment is

pressed.

Inserting/Removing the Drill Bit (see figure B)

– Press the button 5 for drill bit length adjustment and pull

the guide 4 all the way outward.

– Let go of the button 5 again.

– Slide the tip of the drill bit through the dust cap 1/2 from

behind and then fit the bit into the chuck according to the

instructions of your power tool.

– Before removing the drill bit, again press the button 5 and

pull the guide 4 all the way outward.

Adjusting the Guide Length (see figure C)

To ensure that dust is extracted cleanly and the depth stop is

set correctly, the guide 4 must be adjusted so that the tip of

the drill bit is flush at the front with the dust cap 1/2.

Note: To store the dust extraction attachment, press the but-

ton 5 and pull the guide 4 all the way outward. This relieves

strain on the guide’s spring, which increases the lifetime of

the spring.

Adjusting the Drilling Depth (see figure D)

The button 3 for depth stop adjustment can be used to set the

required drilling depth X.

– Press the button 3 and slide the button on the guide 4 so

that the distance X shown in the illustration matches your

required drilling depth.

– Let go of the button 3 again.

Changing the Dust Cap (see figure E)

You will need to change the dust cap 1/2 depending on which

chuck you are using:

–Dust cap 1 for an SDS-plus changeable chuck

–Dust cap 2 for an SDS-plus fixed chuck

You will also need to change the dust cap if the wall contact

surface shows clear signs of wear which is causing dust to es-

cape through the extraction brush during extraction.

Removing the dust cap 1/2:

– Press the locking button 12 and pull the dust cap upwards

out of the holder.

Mounting the dust cap 1/2:

– Insert the new dust cap into the holder from above until the

locking button 12 audibly engages.

Emptying the Dust Box (see figures F1–F4)

Note: Wear a dust mask when performing maintenance and

cleaning on the dust box.

Empty the dust box 13 after completing your work and as

needed, in order to ensure that the dust extraction attach-

ment continues to perform optimally. The viewing window 7

enables you to check how full the dust box is.

– Hold the power tool with the dust extraction attachment

horizontal and switch on the power tool for a few seconds.

This will cause residual dust to be sucked out of the extrac-

tion channel into the dust box 13.

– Insert the required drill bit into

the toolholder of the chuck.

– Press the button 5 while adjust-

ing the guide 4 to match the

drill bit length.

– Let go of the button 5 again.

OBJ_BUCH-2783-001.book Page 8 Friday, September 30, 2016 2:30 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GDE 18V-16 in the language / languages: All languages as an attachment in your email.

The manual is 11.37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GDE 18V-16 Manual

Product: